Table of Contents
On Appliance Part Pros, washing machine belts range in price from around $5 to around $20 and on Amazon, they range in price from around $6 to around $20, so the average cost to repair the belt on a washing machine is around $12 or $13.
How much does it cost to fix a washing machine belt?
Washing machine belt replacement cost is approximately $120 to $175. Washing machine belts are responsible for the spin cycle when cleaning your clothes.
How do I know if my washing machine belt is bad?
Signs The Belt In Your Washer Is Bad It’s a good idea to call for repairs when your washer starts making squealing noises during the wash and spin cycle because the problem just gets worse until the belt breaks. The basket in your washer may also spin erratically or it may stop spinning altogether once the belt breaks.
Is it easy to replace a washing machine belt?
If your washing machine isn’t spinning and there’s no resistance when you rotate the drum, there may be a problem with the drive belt. Fortunately, you can easily replace the belt yourself. It’s important to get a new belt that matches the brand and model of your machine to make sure it fits properly.
How much does a belt cost for a Whirlpool washing machine?
$40.73. Washer main drive belt.
How many belts are on a washing machine?
Most washers have one or two belts. If the spin speed is too slow or items are very wet at the end of the cycle, the belt may be worn out or may have slipped.
Is it worth it to fix a washing machine?
Repair: If the repair would cost less than 50% of the price of a new appliance and your machine still has several expected years of life left, a quick fix could be a cost-effective solution over replacing the entire washer. An active warranty can also make any repair worthwhile.
Can a belt break a washing machine?
The faster the tub spins, the more effectively the water is removed from the clothes or linens. Over time, the drive belt can wear out, break, or slip on the pulleys, resulting in a washer tub that won’t agitate or spin, and, potentially, a drain pump that will be unable to pump water out of the tub.
How many years does a washing machine last?
A typical washer should last 10-13 years. Top-loading washers typically last a few years longer than their front-loading brethren. If you use a stacked washer/dryer combo, you may have to replace both if one starts acting up.
Why is my washing machine belt slipping?
A piece of clothing stuck between the inner and the outer tub on your washing machine or a load that’s too large can stop the drum, which causes the drive belt to slip on the pulley and burn. Take the damaged belt with you to the appliance parts store to get a replacement.
What would cause a washing machine not to spin?
Normally, your washing machine won’t go into a spin cycle until it’s been drained. The drainage hose may become clogged with debris from your clothing, or it could be kinked. If the hose is kinked or crushed, it will likely need to be replaced.
Why is my washing machine making a loud noise when it spins?
If you hear noises when the washing machine is in spin mode, it means that the tub bearing is worn out. When the drum spins, it rides on the bearing which allows it to move freely without any resistance. If the bearing is faulty, you will hear a loud noise when the drum rotates.
Why won’t my washing machine agitate or spin?
Common solutions for: My Washer Won’t Spin or Agitate. Inspect the drive belt to determine if it is broken or if it is loose on the pulleys. If the drive belt is broken or loose, replace it. If the washer is overloaded, the motor coupling will fail in order to protect both the motor and transmission.
Where is the belt in a washing machine?
The belt is located on the underside of your washer and you’ll need the washing machine to be tipped over. Start by putting down towels on the floor to cushion the washing machine when you tip it over.
What would make a Whirlpool washer not spin?
If your Whirlpool washer Not Spinning well, you need to check the pump. It could be clogged with debris or defective and needs to be replaced. To check the pump, disconnect the drain line and remove the back panel of your machine. Check for debris with a flashlight, or check with a special tool.
How do I know if my washing machine needs replacing?
6 BIG WARNING SIGNS YOU NEED WASHER AND DRYER REPAIR OR You Have a Leaking Washing Machine. Your Laundry Machines are Making Strange Noises. Your Washer or Dryer Wanders Across the Laundry Room. Your Washer is Not Filling Correctly. Your Dryer Takes a Long Time to Dry Even Small Loads.
How do you tighten a washing machine belt?
Press the motor into the washing machine and downward or toward the edge of the appliance. With the motor pressed firmly in place, tighten the mounting nut by turning the wrench clockwise. Keep a finger on the belt; when you can depress it only about 1/2 inch with your thumb, you have reached proper tension.
Are washing machine belts Universal?
No they are different lengths and widths depending on your make and model Number of your washer, you will find the model full model number inside the door on an ID label. You have a Belt – 1196J5 the 1195 is the length and the j6 tells you it has 6 ribs on it.
Why does my washer smell like burning?
A burning smell in your washing machine can be a result of a worn clutch, and your machine will likely be making a loud scraping noise during the spin cycle. Another common sign of a worn clutch is brake dust or shavings found underneath the washing machine.
