Table of Contents
When using wood decking, you want a gap of at least 1/8 of an inch after your decking has dried out. If you’re using decking that’s already been dried out, you can leave a 1/8-inch gap when you install. Many decks will use “green” wood, or wood that hasn’t been dried down or kiln dried.
Should deck boards have a space between them?
Proper deck board spacing should have a 1/8-inch gap after the decking has dried out. If you install your decking using wet boards, pressure-treated decking that has not yet dried out, then you should install them with no gap as a gap will be created as they dry and shrink.
How much space should be between 2×6 deck boards?
The Sweet Spot – Most people agree that 3/16” is a good gap between boards. Going more than a ¼” may get a little too wide. The width of a nail head is just about right. Treated Lumber – Usually treated lumber will have some shrinkage so you can butt the boards almost right against each other during installation.
Should deck boards be butted together?
We recommend butting treated deck boards together because as the moisture dries from the wood, the boards will shrink and naturally form gaps to allow water drainage. (Depending on moisture content, cedar, cypress and especially hardwood decking may require deliberate spacing for consistent joint sizes.)Jun 21, 2010.
Can you put deck boards tight together?
Keep the butt ends as tight as possible when installing wood decking. This rule does NOT apply to composite or PVC boards which can have a large thermal expansion; enough to create a serious roller coaster effect down the length of the PVC or composite boards if you DON’T leave room for thermal expansion.
Do deck boards shrink or expand?
Any type of decking board will expand and shrink, whether it’s wood, plastic, or composites. However, they don’t change in size as much as wood or plastic. Wood fibres hold the shape when the composite undergoes thermal expansion, while the plastic fibres do the same when moisture is involved.
What is the correct way to lay decking boards?
What is the correct way to lay decking? Any decking board manufacturer or professional will tell you: “The proper way to install a decking board is ridge side down.” The ridges are designed to allow for airflow, to stop moisture sitting in the ridge, and allow for a stronger structure.
How do you layout deck boards?
Deck boards should sit 1 ½” off the edge of each side of your deck. Use your straightest deck board and lay it first across the deck’s front edge, opposite your house. Each board should have a ⅛” gap. All deck board should end on a joist, making sure to stagger deck board ends.
How do you fill space between deck boards?
While you might be tempted to fill in gaps in your decking with wood filler or caulk, the natural movement of the boards can eventually cause the materials to break loose and make the gaps even worse. However, you can use rope to easily fill the gaps.
Do you screw decking at every joist?
Each deck board should be fastened with two screws at each point where the board crosses a joist to ensure the stability and durability of your deck’s surface. Boards should be fastened to rim joists with three screws.
Why do you stagger deck boards?
Staggering the deck boards decreases the number of screws or nails going into one joist, which can weaken or rot the joist more quickly. Staggering the joints strengthens the deck by spreading the seams across more joists instead of placing the stress on only one.
Where do you start laying deck boards?
In most cases, it’s best to start with a full board on the outside edge of the deck and work toward the house so the odd board is less visible. Then measure when you’re 4 to 5 ft. away from the house and adjust the gap sizes to be sure the last board is a consistent width.
Should you space 5 4 decking?
For 5/4 pressure treated decking, it should be installed tight and allowed to shrink to provide water drainage. With cedar 5/4 decking installation should be with 1/16″-1/8″ gap (2-3mm), which will expand to 1/8-1/4″ (3-6mm) once the wood has dried. Providing both deckings’ plenty of spacing for drainage.
What happens if you don’t space deck boards?
Without the right deck spacing, the boards may expand, cup, and buckle out of place. As a result, you may have to replace broken decking, or reinstall the boards with wider spacing to prevent further cupping and buckling, which can be time consuming and expensive.
Do you space pressure treated deck boards?
Leave a gap between pressure treated deck boards when the wood is wet. Leave Gap: If the pressure treated wood has been kiln dried after treatment (KDAT), leave a 1/8” gap (the thickness of an 8-penny nail) between the boards when attaching, since the wood will expand slightly over time.
How do I calculate deck spacing?
Square footage of board spacing = (S) x Length of deck Then multiply 0.26 feet by 16 feet to get 4.16 square feet, the total area of board spacing.
How far apart should decking joists be?
Deck joist spacing should never exceed 16″ on center (with the exception of MAX deck boards, which allow for maximum 24″ on center). For a more rigid feel, 12″ or less may be preferred. If adding additional framing, be sure to keep all boards level and in plane across the tops.
