Table of Contents
How much does it cost to do a tub surround?
Cost To Install Tub Surround The average cost to install a tub surround is $600 to $1,800 for the materials and labor. The labor cost to replace a tub surround is $300 to $600. Basic acrylic and fiberglass tub surrounds cost $200 to $1,000, while solid surface surrounds cost $600 to $2,000, plus installation.
How long does it take to install a tub surround?
For a typical tub with a tile tub surround to be removed and the walls of the surround replaced you are looking at at least 3 days for simple tile, although there are ways to shorten this. It will take about a half day to get rid of the old one.
How much is shower surround installation?
The national average materials cost to install a shower surround is $226.39 per surround, with a range between $203.11 to $249.67. The total price for labor and materials per surround is $594.63, coming in between $531.47 to $657.79.
Can you put a tub surround over existing tub?
Tub surrounds can sometimes be installed over existing tile, but only when conditions are right. The old tile area needs to be smaller than the kit and you’ll need to build up the surrounding wall to the level of the tile, usually with 1/4-in. drywall. First, tape cardboard over the tub to protect it.
How long does it take to tile a tub surround?
Expect to spend about 20 minutes per square yard to prepare and set the tile, and make sure you’re comfortable with using hand tools, a cordless drill, and trowels. Depending on the size of your shower and your expertise level, the project can be accomplished in a few days.
How long do tub surrounds last?
Swanstone bathtub surrounds You can order matching solid-surface trim kits that eliminate the need for tile around the edge. Expect a life span of 30-plus years. Some brands include a lifetime warranty.
Do you need drywall behind a tub surround?
The short answer to the question is, “It’s not recommended.” However, this answer only really only suffices if you’re converting a room that was never a bathroom into a wet space. Drywall on its own is not suitable for use in bathrooms because it is prone to absorbing moisture and thus losing structural integrity.
Do you put drywall behind a shower surround?
Fiberglass and acrylic tub and shower enclosures come with a flanged edge that attaches directly to the wall studs, and the proper way to hide this flange is to install drywall over it. Consequently, enclosures are typically installed on the bare studs.
How much does it cost to install a shower tub combo?
Shower/tub combos cost around $300 to $700 for a fiberglass surround, and they usually take a few hours to install with the plumbing. Installing a shower/tub combo is usually a little more involved than a stall, so plan to pay $600 to $800 for the installation of the unit and fixtures.
Are bath Fitters expensive?
The lowest price of a bath fitter is $800, and the highest is around $3,500. On average, a bath fitter, labor, and any modification would incur an estimated cost of about $1,000 to upwards of $10,000. The total cost depends on variables, e.g., the quality of material, size of a bathtub, and finishes.
Can I install Bath Fitter myself?
Bathtub liners have to be custom made to fit, so even if you install one yourself, it could involve long waiting periods. You can hire a pro to do it, or you may choose to do it yourself with a bathtub refinishing kit. To prepare the area, first turn off the water source, clean the tub and remove any existing caulk.
How do you prepare a tub surround for tile?
Tub or shower wall tile preparation: Apply a layer of 1/2″ thick cement backer board to the wall studs. Tape any seams and corners with fiberglass tape. Apply thin-set adhesive over the fiberglass tape, and allow it to dry. Roll a waterproofing sealer over the walls, and allow the sealer to dry.
Is it cheaper to tile a shower or buy a surround?
Because they are less laborious to install, surrounds are often less expensive than tile. Some high-end materials, however, such as granite, may be more expensive than tiling with some grades of tile.
Is a tub surround a good idea?
Surrounding the walls of your bathtub with waterproof material is essential when building or remodeling your bathroom. Instead, many homeowners choose bathtub liners or wall surrounds, which adhere to the walls and protect them from moisture, mold and mildew.
Are tub surrounds easy to install?
Tub surrounds and shower surrounds are easy to install and maintain. Follow our ten steps to update your bathroom with a surround. Installation can vary from product to product, so read the manufacturer’s instructions carefully.
Do you need cement board behind tub surround?
ANSWER – No there should not be a gap between the top of the bathtub flange and the backer board on the wall. There should be a moisture barrier behind the backer board that is installed in a weather lapping manner starting at the tub flange working up the wall.
Do you need cement board behind shower surround?
Special protection is needed behind showers and tubs to prevent moisture from seeping into the wall structure. Non-paper-faced fiber-reinforced gypsum board, moisture-resistant gypsum board, or “green board” products are also not recommended behind tub surrounds (BSC 2009a).
