Table of Contents
How do you calculate crusher run?
Multiply the length (L), in feet, by the width (W), in feet, by the height (H), in feet, and divide by 27. This number is how many cubic yards of crushed stone you need. When using this equation, make sure all your measurements are in feet.
How much will a yard of crusher run cover?
Calculate Crusher Run Coverage (Square feet) 400 sq ft Volume (Cubic yards) 2.5 cu yd Estimated amount (Pounds) 5,951 lb Estimated amount (Tons) 2.98 ton Amount +15% compression 3.42 ton.
How much crusher run do I need for my patio?
A rule of thumb for many crushed stone projects is to have a minimum depth of 2 to 4 inches, although some projects require more. For example, a patio that’s 12-foot square, with a 2-inch base of crushed stone, will need 0.89 cubic yards.
How many tons is a cubic yard of crusher run?
Most of gravel and crushed stone products have similar weight, gravel and crushed stone typically weighs around 2800 pounds per cubic yard, it means 1 cubic yard of gravel weight is 2800 lb and in United States, 1 ton of gravel is equal to 2000 pounds, number of ton in a cubic yard of gravel = 2800/2000 = 1.4 tons, so.
How thick should crush and run be?
Add and compact crusher run in 4-inch layers until the rough driveway form is achieved. Two to three layers of crusher run are typically required to reach this point, depending on the depth of the excavated driveway space.
How much is a ton of crusher run?
Crush & Run Cost per cubic yard is about $20 and per ton about $28. This material—also known as crusher run, quarry process, dense grade aggregate, or road stone—is the combination of crushed rock and dust created in the process.
How much does crush and run weight per cubic yard?
One cubic yard of gravel can weigh between 2,400 to 2,900 lbs. Or up to one and a half tons approximately. Generally, a cubic yard of gravel provides enough material to cover a 100-square-foot area with 3 inches of gravel. Keep in mind that some materials compact more than others, so exact coverage may vary.
How much does crush and run weight per yard?
Crusher run is ordered by the ton. Since crusher run weights approximately 2,500 lb. per cubic yard, first determine the volume requirement of your project.
How much does a dump truck of crush and run cost?
Crush and Run Prices. Crush and run gravel costs $24 to $34 per ton, about $50 per cubic yard, or $0.50 to $2.00 per square foot, which is one of the cheapest materials. This mixture combines limestone, trap rock, granite, crushed rock, sand, and stone dust.
How many ton of gravel do I need?
Length in feet x Width in feet x Depth in feet (inches divided by 12). Take the total and divide by 21.6 (the amount of cubic feet in a ton). The final figure will be the estimated amount of tons required.
How do you calculate gravel for a patio?
Gravel Calculation Normally you want a base layer of gravel about 4-inches deep. Four inches is one-third of a foot, so multiply the square footage by one-third to find the cubic feet of gravel you need. For a 120-square foot patio that works out to 40-cubic feet of gravel.
What area does a ton of gravel cover?
Type 3 Aggregate Calculator Un-compacted Cloburn aggregates weigh 1.4 tonnes per cubic metre. Therefore if you wish to apply them at a 50mm depth (the normal depth for a driveway) one tonne will cover 14 square metres.
How much crush and run can a dump truck hold?
Typically, larger dump trucks can carry about 28,000 pounds or about 14 tons. On average, smaller dump trucks can transport around 13,000 to 15,000 pounds or 6.5 to 7.5 tons.
How many yards is 10 tons?
Ton Register to Cubic Yard Conversion Table Ton Register [ton Reg] Cubic Yard [yd^3] 2 ton reg 7.4074074074 yd^3 3 ton reg 11.1111111111 yd^3 5 ton reg 18.5185185185 yd^3 10 ton reg 37.037037037 yd^3.
How many cubic feet are in a ton of gravel?
How much is a ton of gravel? A ton of gravel with average-sized pebbles is about 0.705 cubic yards, or 19 cubic feet, assuming it has been screened for debris and contains no leftover dirt, sand, etc.
Is crush and run good base for driveway?
Crusher run is a mix of 57 Granite and Granite Fines which makes it ideal for drainage, expanding and contracting with temperatures, and compaction when used as a base. Make sure to have a way to secure the sides of your driveway with this product, as the granite Fines (sandy material) can wash a little over time.
Can you pour concrete over crusher run?
Simply pouring concrete onto the ground will expose it to elemental erosion that will cause cracking and sinking. Similarly, if there are roots or plants under your slab, they may rot and cause unevenness. Pouring concrete over crushed stone, however, will eliminate these worries.
Is crush and run good for a driveway?
Crush and run gravel is made from tiny pieces of gravel that is mixed with limestone. This is a useful top layer for gravel driveways because the limestone sticks together when wet, helping the driveway last longer. Crush and run gravel driveways are affordable and can last for years if they are properly maintained.
