Table of Contents
How many yards is 30×40 of concrete?
assuming the normal 4″slab the volume would be theoretically 9.875 yards, so this will be rounded up to 10 yards (cubic).
How do I figure out how many yards of concrete I need?
How do I calculate how much concrete I need for a slab? Measure the area in feet. Multiply length by width, and then by thickness. Divide the resulting number by 27 to find cubic yards.
How much concrete do I need for a 30×30 slab?
18 yards of 3000 psi concrete mix @ 135.00 per yard. Wire mesh reinforcement. A double row of #4 rebar around the edges. Labor to form the slab.
How many yards of concrete do I need for a 24×24 garage?
For example, for a concrete slab that is 24′ X 24′ X 4”, simply enter 4 in the Thickness/Depth field, 24 in the Width field, and 24 in the Length field. Click “Calculate”. Your answer should be 7.11 yards. Note: The Concrete Volume Calculator can also be used to determine yardage for aggregate products.
How many yards of concrete do I need for a 10×10 slab?
The amount you will need for a 10 x 10 slab is 1.3 cubic yards, we always add an extra 10% to allow for any slab depth variations or spills that may occur.
How many square feet is a yard of concrete 4 inches thick?
One Cubic Yard of Concrete: 4-inches thick – covers 81 square feet.
How thick should a concrete slab be?
Standard concrete floor slab thickness in residential construction is 4 inches. Five to six inches is recommended if the concrete will receive occasional heavy loads, such as motor homes or garbage trucks. To prepare the base, cut the ground level to the proper depth to allow for the slab thickness.
How much does it cost to pour a 24×24 slab of concrete?
A typical 24×24 garage slab costs between $3,057 and $5,944 with prices ranging from $5.31 to $8.31 per square foot for a 4” reinforced slab of concrete, and $6.83 to $10.32 per square foot for a 6” slab of reinforced concrete.
How much area is a yard of concrete?
How much concrete is in a yard? Concrete volume is measured in cubic yards. When poured on a perfectly level surface, one cubic yard will cover 27 square feet at one foot thick.
How much is a 10×20 concrete patio?
How Much Does a 10×20 Concrete Patio Cost? A concrete patio costs between $4 and $12 per square foot, including materials and labor. Based on those estimates, a 10-foot by 20-foot concrete patio would cost between $800 and $2,400.
How many bags of concrete do I need for a 10×10 slab 4 inches thick?
The thickness of your 10′ x 10′ slab will determine just how many bags you need. The average thickness of a 10′ x 10′ concrete slab for a shed is 4 inches thick. At 4″ thick, your 10 x 10 slab will take 56 bags of concrete that weigh 80 lbs.
How thick does a concrete slab need to be for a garage?
The concrete slab should be four inches thick at least; it needs to be thicker if heavy equipment will rest on it. Building codes offer requirements for the concrete mix, which vary by region. The standards are expressed in terms of “compressive strength,” which boils down to the amount of water used in the mix.
How many yards of concrete does a concrete truck hold?
Each cubic yard costs about $65. However, a fully loaded cement truck will hold 10 cubic yards—and partial “short” loads cost $15 to $20 extra for every cubic yard less than a full load.
How many 80 lbs bags of concrete make a cubic yard?
One 80lbs bag of Quikrete Concrete Mix will yield approximately . 60 cu ft. So it will take 45 bag to equal one cubic yard of concrete. If you have a project over a 1/2 a cubic yard you should consider our Mix On-site Concrete especially if you are hand mixing.
How thick should a concrete patio be?
Four inches is the minimum thickness for a concrete patio. You’ll want to make it six to eight inches thick if the patio will support a structure such as a gazebo or hot tub.
How much area does a 40 lb bag of concrete cover?
Regarding this, how much does a 40 lb bag concrete cover, as 133 lb concrete = 1 CF, so a bag of 40 lb concrete = 40/133 = 0.30 CF, therefore, a 40 lb bag concrete approximately cover around 1.8 square feet area upto depth of 3 inch.
How much does an 80 pound bag of concrete cover?
80 lb bag of concrete cubic feet 80 lb bag of concrete yields 0.60 cubic feet which is approximately around 0.0222 cubic yards that will cover around 3.6 sq ft area up to standard depth of 2 inch excavation or backfills, and for 1 cubic feet of landfill you will need 1.66 bags of 80 lb concrete.
Do you need rebar for 4 inch slab?
The thickness of rebar should be no more than 1/8 that of the slab, so a 4” slab shouldn’t have steel greater than #4 or 1/2″ bar. It’s best to check with a Structural Engineer if your slab will bridge or cantilever. What is this? For 4” concrete slabs used for driveways and patios, #3 rebar is common.
How many square feet is 3 cubic yards?
Cubic yard to Square feet Calculator 1 cubic yard = 9 ft 2 0.037 cubic yard 3 cubic yard = 18.7208 ft 2 0.1925 cubic yard 4 cubic yard = 22.6786 ft 2 0.2963 cubic yard 5 cubic yard = 26.3162 ft 2 0.4141 cubic yard 6 cubic yard = 29.7173 ft 2 0.5443 cubic yard.
What does 1 yard of concrete weigh?
Concrete Weight per Cubic Yard A solid slab of concrete weighs 4,050 pounds per cubic yard. A cubic yard of broken up concrete weighs 2,025 pounds.
How do I calculate square feet into yards of concrete?
To convert square feet to cubic yards, you simply multiply your square footage figure by the height or depth of the area (in feet) to get a volume measurement in cubic feet. You then divide the total by 27 to get your measurement in cubic yards.
