Table of Contents
For example, for a concrete slab that is 24′ X 24′ X 4”, simply enter 4 in the Thickness/Depth field, 24 in the Width field, and 24 in the Length field. Click “Calculate”. Your answer should be 7.11 yards. Note: The Concrete Volume Calculator can also be used to determine yardage for aggregate products.
How many square feet does 10 yards of concrete cover 4 inches thick?
4-inches thick – covers 81 square feet. 5-inches thick – covers 65 square feet.
How do you figure out how many yards of concrete you need?
How do I calculate how much concrete I need for a slab? Measure the area in feet. Multiply length by width, and then by thickness. Divide the resulting number by 27 to find cubic yards.
How much concrete do I need for a 20×20 garage?
Garage Slab Cost Garage Foundation Size 4” Slab Cost 6” Slab Cost 1-car Garage (10×20) $1,062 – $1,662 $1,366 – $2,064 2-car Garage (20×20) $2,124 – $3,324 $2,732 – $4,128 3-car Garage (30×20) $3,156 – $4,986 $4,098 – $6,192.
How many yards of concrete do I need for 10×10?
The amount you will need for a 10 x 10 slab is 1.3 cubic yards, we always add an extra 10% to allow for any slab depth variations or spills that may occur.
How thick should a concrete slab be?
Standard concrete floor slab thickness in residential construction is 4 inches. Five to six inches is recommended if the concrete will receive occasional heavy loads, such as motor homes or garbage trucks. To prepare the base, cut the ground level to the proper depth to allow for the slab thickness.
How many yards of concrete does a concrete truck hold?
Each cubic yard costs about $65. However, a fully loaded cement truck will hold 10 cubic yards—and partial “short” loads cost $15 to $20 extra for every cubic yard less than a full load.
What is the formula for figuring out concrete?
Use the formula. Calculating the volume for concrete requires using three dimensions: length times width (which is area) times the height (thickness) or L x W x H. If you are using feet as your standard unit of measurement, this formula will give you the volume of concrete in cubic feet.
How much cement do I need for a 12×12 slab?
Regarding this, “how much concrete do I need for a 12×12 slab?”, at 4 inches thick, generally you will need approximately 1.76 cubic yards or 47.52 cubic feet or 1.35 m3 (either 104 bags of 60lb or 80 bags of 80lb) of premixed concrete for a 12×12 slab, at 5 inches thick slab, 2.22 cubic yards or 59.90 cubic feet or.
How thick should a concrete patio be?
Four inches is the minimum thickness for a concrete patio. You’ll want to make it six to eight inches thick if the patio will support a structure such as a gazebo or hot tub.
How much concrete do I need for a 30×30 slab?
18 yards of 3000 psi concrete mix @ 135.00 per yard. Wire mesh reinforcement. A double row of #4 rebar around the edges. Labor to form the slab.
How much would it cost to pour a 20×20 concrete slab?
But how much does a 20×20 concrete slab cost? You can expect to pay between $1,600 and $3,200 for a 20×20 slab. The estimates are based on the average cost of $4 to $8 per square foot for a concrete slab. Yet, the costs may vary.
How thick should a concrete driveway be?
As for thickness, non-reinforced pavement four inches thick is standard for passenger car driveways. For heavier vehicles, a thickness of five inches is recommended. To eliminate standing water, the driveway should be sloped towards the street a minimum of one percent, or 1/8 inch per foot, for proper drainage.
How much area does a 40 lb bag of concrete cover?
Regarding this, how much does a 40 lb bag concrete cover, as 133 lb concrete = 1 CF, so a bag of 40 lb concrete = 40/133 = 0.30 CF, therefore, a 40 lb bag concrete approximately cover around 1.8 square feet area upto depth of 3 inch.
How much does an 80 pound bag of concrete cover?
80 lb bag of concrete cubic feet 80 lb bag of concrete yields 0.60 cubic feet which is approximately around 0.0222 cubic yards that will cover around 3.6 sq ft area up to standard depth of 2 inch excavation or backfills, and for 1 cubic feet of landfill you will need 1.66 bags of 80 lb concrete.
How much area does an 80 pound bag of concrete cover?
15 cubic feet for every 20 pounds of mix, so a 40-pound bag yields . 30 cubic feet, 60 pounds of concrete mix yields . 45 cubic feet and an 80-pound bag yields . 60 cubic feet.
HOW MUCH CAN 4 inches of concrete hold?
Typically we like to limit the weight to about 40 lb/sqft on an unknown 4″ slab. In most cases you can go to 80 lb/sqft in isolated spots, but unless you know roughly what the soil bearing and reinforcing is for that slab you might be looking at cracking.
Do you have to put gravel down before pouring concrete?
Because concrete is a very porous material, it will absorb any moisture that it contacts. This can cause pooling. Without crushed stone, pooling water will settle under it and erode your slab. Adding a layer of crushed stone will add proper drainage, as well as create a barrier between your slab and the ground.
Is 4 inches of concrete enough?
For a concrete patio, the ideal slab thickness is at least four inches. There are times where thicker slabs will make more sense, but, most of the time, 4 inches is the perfect thickness for a concrete slab. It is, however, wise to make the perimeter of the slab an inch or two thicker.
