Table of Contents
Each cubic yard costs about $65. However, a fully loaded cement truck will hold 10 cubic yards—and partial “short” loads cost $15 to $20 extra for every cubic yard less than a full load.
How many yards of cement can a cement truck carry?
Concrete trucks weigh an average of 25,000 lbs. by themselves and up to 40,000 lbs. when carrying a full load. Their capacity is around 8 cubic yards, but can be up to 10 cubic yards if fully-loaded.
Is it cheaper to mix your own concrete?
One of the least expensive ways to get concrete is to mix your own. You can buy bags of the mix from a home improvement store. Otherwise, you risk getting a weaker concrete once it cures, which could lead to cracks or crumbles within a couple of years.
How much does a yard cement cost?
Concrete costs an average of $117 per cubic yard, with a typical range between $104 and $144 per cubic yard. Concrete costs an average of $117 per cubic yard, with a typical range between $104 and $144 per cubic yard.
How many yards of concrete do I need for a 24×24 slab?
For example, for a concrete slab that is 24′ X 24′ X 4”, simply enter 4 in the Thickness/Depth field, 24 in the Width field, and 24 in the Length field. Click “Calculate”. Your answer should be 7.11 yards. Note: The Concrete Volume Calculator can also be used to determine yardage for aggregate products.
How much does it cost to pour a 24×24 slab of concrete?
A typical 24×24 garage slab costs between $3,057 and $5,944 with prices ranging from $5.31 to $8.31 per square foot for a 4” reinforced slab of concrete, and $6.83 to $10.32 per square foot for a 6” slab of reinforced concrete.
How much does it cost to pour a 20×20 concrete slab?
But how much does a 20×20 concrete slab cost? You can expect to pay between $1,600 and $3,200 for a 20×20 slab. The estimates are based on the average cost of $4 to $8 per square foot for a concrete slab. Yet, the costs may vary.
Is it cheaper to get a concrete truck or bags?
However, a fully loaded cement truck will hold 10 cubic yards—and partial “short” loads cost $15 to $20 extra for every cubic yard less than a full load. For this project, ordering ready-mix would cost from $55 to $120 more than premixed — depending on where you buy your bags and rent your mixer.
How much concrete do I need for a 10×10 slab?
The amount you will need for a 10 x 10 slab is 1.3 cubic yards, we always add an extra 10% to allow for any slab depth variations or spills that may occur.
How many 80lb bags of concrete make a yard?
One 80lbs bag of Quikrete Concrete Mix will yield approximately . 60 cu ft. So it will take 45 bag to equal one cubic yard of concrete.
How much does it cost to pour a 20×30 concrete slab?
The average cost of a 20×30 concrete slab is between $2,400 and $4,800. The median price is about $3,600. However, the thickness of the slab and other features may increase or lower the cost.
How many sq ft does a yard of concrete cover?
How much concrete is in a yard? Concrete volume is measured in cubic yards. When poured on a perfectly level surface, one cubic yard will cover 27 square feet at one foot thick.
How thick should a concrete slab be?
Standard concrete floor slab thickness in residential construction is 4 inches. Five to six inches is recommended if the concrete will receive occasional heavy loads, such as motor homes or garbage trucks. To prepare the base, cut the ground level to the proper depth to allow for the slab thickness.
How do I figure out how many yards of concrete I need?
How do I calculate how much concrete I need for a slab? Measure the area in feet. Multiply length by width, and then by thickness. Divide the resulting number by 27 to find cubic yards.
How much cement do I need for a 12×12 slab?
Regarding this, “how much concrete do I need for a 12×12 slab?”, at 4 inches thick, generally you will need approximately 1.76 cubic yards or 47.52 cubic feet or 1.35 m3 (either 104 bags of 60lb or 80 bags of 80lb) of premixed concrete for a 12×12 slab, at 5 inches thick slab, 2.22 cubic yards or 59.90 cubic feet or.
How thick should a concrete driveway be?
As for thickness, non-reinforced pavement four inches thick is standard for passenger car driveways. For heavier vehicles, a thickness of five inches is recommended. To eliminate standing water, the driveway should be sloped towards the street a minimum of one percent, or 1/8 inch per foot, for proper drainage.
How much concrete do I need for a 40×60 shop?
How much does a 40×60 concrete slab cost? It would be about $8,500 to $12,000 for a 40×60 foot concrete slab, 6 inches thick. That’s based on national averages of around $5 per square foot for a fully engineered, finished concrete slab, including labor and materials.
How much concrete do I need for a 30×30 slab?
18 yards of 3000 psi concrete mix @ 135.00 per yard. Wire mesh reinforcement. A double row of #4 rebar around the edges. Labor to form the slab.
