Table of Contents
A rule of thumb with springs is that four quarter turns equals a full revolution and the spring needs to be tightened a full revolution for every foot of door height (e.g. 7-1/2 foot door = 7 revolutions +2 (30 quarter turns).
Which direction do you wind a garage door spring?
Basically, door springs can either wind to the left or to the right. Right-hand winding springs wind in a clockwise manner with the end wire on the right, while left-hand winding springs go anticlockwise with their end wire on the left.
How much tension should be on a garage door spring?
You would want to tighten the adjuster a full turn clockwise to add tension if the door closed easily without holding up halfway. However, you will want to loosen the adjuster three turns counterclockwise if it was too tight.
How do you wind a garage door torsion spring?
How to Wind Garage Door Torsion Springs Insert one winding rod snugly into winding cone, to full socket depth. Maintaining a tight grip on the winding rod rotate it slowly in the proper direction, as shown below.
How many turns on a 8ft garage door spring?
A) The amount of turns required on your springs depends on the height of your garage door. If your door is 7ft high then we recommend starting off at 31 Quarter turns on each springs. If you have an 8ft door then start at 34 Quarter turns.
How much tension should be on a garage door torsion spring?
One option is to add tension to the springs. For example, if the door is 40 pounds heavy on the floor, you can adjust the springs on torsion spring doors to reduce the weight to 20 pounds. But even so, closing the door will require an extra 20 pounds of pull or opener force.
What is the color code on garage door springs?
Garage Door Extension Spring DASMA Color Code Chart Color Pounds Kilograms Brown 60/160/260 xxx Orange 70/170/270 30/75/120 Gold 80/180/280 35/80/125 Light Blue 90/190/290 40/85/130.
How do you tell a right and left spring on a garage door?
Look at the end of the spring to determine the wind direction. If the end of the spring points in the clockwise direction it is left-wound and if the end of the spring points in the counter-clockwise direction, it is right-wound.
Do torsion springs work in both directions?
Torsion springs are helical springs that exert a torque or rotary force. Depending on the application, a torsion springs can be designed to work in a clockwise or counter-clockwise rotation, thus determining the direction of the wind.
How many turns on a 9ft garage door spring?
A rule of thumb with springs is that four quarter turns equals a full revolution and the spring needs to be tightened a full revolution for every foot of door height (e.g. 7-1/2 foot door = 7 revolutions +2 (30 quarter turns).
Can you over tighten garage door springs?
1) Secure the door in place by putting a C-clamp on the garage door track above the bottom-most door roller. As you adjust the spring more tightly, there is the chance that the door may begin to rise if you overtighten it a dangerous possibility!.
How do I know if my garage door springs need to be adjusted?
More Noise Than Usual. A balanced garage door should be relatively quiet when traveling up or down the door tracks. If your garage door is making excessive creaking, grinding, or squeaking noises when opening or closing, your springs may be strained and most likely need to be replaced.
What weight garage door springs do I need?
This is determined by the pitch with which the springs are wound. On sectional garage door springs, this normally is 15 percent. For example, a 100-pound pull spring requires 15 pounds of weight to separate the coils; when a door is open, the two springs will support 15 pounds of door weight without any stretch.
Why do torsion springs break?
The springs on your garage door system are responsible for the heavy lifting. When the garage door is lowered, the springs gain tension. When raising the garage door, tension is released and the spring assists with the lifting. As a result, most garage door springs break when the door is down.
How many turns on a 8ft garage door?
If you didn’t get a recommendation, perform 30 quarter turns for a 7-ft. -tall door and 36 quarter turns for an 8-ft. -tall door.
Can I use a different size garage door spring?
When you add everything up, you have the exact weight once done; you can then use two different size springs if it yields optimal balance. If you are a homeowner and the technician used two different size springs, don’t be alarmed. What matters is that the garage door is balanced.
Can I put a bigger spring on my garage door?
If your garage door springs have lasted less than five years, or if you plan to live where you are for many years, you may want to try the extra long life torsion springs. By using larger springs, you can, in most cases, quadruple your spring life while only doubling the cost of the springs.
Can garage door springs be too strong?
When garage door springs are too large, they provide more strength than the door needs. It will open with too much force, rolling up very quickly and compromising its safety. Kids or even unprepared adults could be knocked over by the sudden force when they try to open it.
