Table of Contents
Therefore you need 6 clips per one long egde and 12 clips per both long egdes. if the rafters are 24 inches O.C. and the plywood sheet is 8”, then you need 4 clips for 1 side and 8 for both sides. Longer plywood sheet could need more clips.
How far apart should h clips be?
pair of trusses, rafters, or joists. However, two (2) equally spaced H-clips are required between supports when spaced 48 inches on center. misfit of abutting sheets may be tolerated if gaps do not exceed maximum opening of 1/4 inch (6 mm).
Are H clips required for 5/8 roof sheathing?
5/8” thick panels having a span rating of 40/20 can have an unsupported edge up to 32”. This means that 1/2” and 5/8” thick roofing panels that are supported by roof framing (rafters or trusses) spaced at the typical 16” or 24” o.c. do not require edge support (H-clips).
Are clips required for roof sheathing?
For the most common roof sheathing in our area, which is 1/2” nominal (7/16” actual) sheathing over trusses or rafters at 24” on center, there is no requirement for H-clips. One or two H-clips will often allow a longer span between roof trusses/rafters.
What do H-clips do?
H-clips, also called panel-edge clips, are small steel devices that fit snugly between wood panels in order to provide them with edge support. They are often used with roof sheathing to keep it from feeling spongy or soft at its edges.
Are H-clips code?
H-clips are an architects or engineer’s call, not a code requirement. 7/16″ OSB very commonly spans rafters 24″ on center without clips. Not required by most residential codes unless your area has special requirements.
How many plywood clips do I need?
How many do I need for each sheet of plywood? Answer: You need 1 clip per a rafter bay/cavity. If the rafters are 16 inches O.C. and the plywood sheet is 8 foot long, then you get 6 bays/cavities.
Where do you put plywood clips?
The clips are inserted over the edges of the adjacent plywood panels to reduce deflection of the panel edges between the framing members and are most commonly used for roof sheathing. Plywood clips are inserted by hand and the procedure is done in conjunction with installation of the sheathing.
Which is better for roofing OSB or plywood?
Plywood Holds the Moisture Advantage Over OSB When plywood gets wet, it tends to swell. OSB takes longer than plywood to get saturated, but also takes much longer to dry out. When used as roof sheathing, this tendency to hold moisture means it will degrade faster than plywood when exposed to chronic leaks.
What is the minimum thickness of roof sheathing?
Sheathing must be a minimum of 19/32-inch thick. Never affix roof sheathing with staples; 8d ring-shank nails need to be used instead. The normal thickness range for sheathing is 3/8 to 3/4 inch.
How far should roof sheathing overhang fascia?
Ideally the sheathing should be on top of the fascia without extending beyond it. Guesswork can create a situation in which it extends too far and it interferes with flashing installation, or you have to cut it. If the fascia is to be one layer of 1x, I overhang the sheathing 5/8.
What is the nailing schedule for roof sheathing?
As such, the nailing schedule is typically the familiar 6 inches on center at supported panel edges, including gable-end walls and 12 inches on center over intermediate panel sup- ports. Note, however, that minimum 8d nails (0.131 x 2-1/2 inches) are recom- mended for all panels 5/8 inch thick or less.
Does sheathing overlap fascia?
Notice that when the fascia is placed, the top edge of the fascia is even with the top of the sheathing. In view B, the sheathing overlaps the tail end of the rafter by the thickness of the fascia material.
What should I use for roof sheathing?
Typical types of wood used for roof sheathing are oriented strand board, known as OSB, and plywood, the most popular being OSB. Sheets of 7/16-inch thick, with no edge support, can be used in an area where the snow load is 30 pounds per square foot. With edge support and the same snow load, 3/8-inch OSB can be used.
What is roofing sheathing?
Roof decking (or roof sheathing) is the wooden boards that make up the foundation of your entire roof system. I like to say foundation because it’s what your shingles and the rest of your roofing components are installed on. Roof decking is one of the most important pieces of your roof system.
What are hurricane clips?
Hurricane clips are metal straps that connect the roof truss to the top of a wall. That way, the roof system won’t blow off during a hurricane.
What is a roof truss in construction?
A roof truss is best described as a structural framework of timbers that’s designed to provide support for a roof. They’re also used to bridge the space above a room. For trusses, the triangular webbing of structural pieces not only provide support for the roof, but they also tie the outside walls of the home together.
How thick should roof plywood be?
Most roofs will be sheathed in plywood at least 3/8 inch thick. That will suffice on a roof with rafters set 16 inches apart with minimal roof loads. Loads will vary with the pitch of the roof; the flatter the roof, the greater the load on any one section. Steeper roofs will have lighter loads per square foot.
How many sheets of plywood do I need for my roof?
Divide the total roof area by 32 to get the number of sheets you will need to cover the roof. A typical 4 foot by 8 foot sheet of plywood covers 32 square feet. If your roof area is 1,600 square feet, 1,600 divided by 32 will mean you need about 50 sheets to cover the roof.
Can you lay roof sheathing vertically?
Installed vertically, the same panel can only handle gusts up to 110 mph on the same stud spacing. The IRC, meanwhile, allows you to orient the sheathing in either direction for wind loads, but includes an important exception: If you’re using 3-ply plywood panels of any thickness on studs spaced greater than 16 in.
What is a roof clip?
To begin, let’s define a clip: It’s a concealed anchor that attaches a metal panel to the substrate (roof deck or other material beneath the metal panels) with the use of fasteners. Clips are sometimes referred to as cleats as well. Clips can come in a variety of metal materials and gauges, including: Galvalume®Dec 5, 2018.
