Table of Contents
How do you arrange ceramic logs in a gas fireplace?
How to Arrange Gas Logs Place the largest ceramic logs on the bottom to serve as the foundation for the fire. Leave 2 inches (5 centimeters) between logs. Make sure none of the logs is blocking the gas flow. Arrange smaller logs on top of the foundation logs.
How do you measure for ceramic fireplace logs?
How to Measure Your Fireplace for Gas Logs Measure the front opening of your fireplace. Measure the back width of your fireplace. Measure the depth of the floor from back wall to the front of your fireplace. Measure the inside height of the fireplace from the floor to the lowest point inside the fireplace.
Do you need ceramic logs in a gas fireplace?
Fake gas fireplace logs are made of ceramic or a similar material. Without them, most of the heat from the burning gas would just escape out the vent. By retaining more heat, the ceramic provides warmth and comfort for your home.
How do I arrange my gas fire coals?
‘The coals must not be crammed together, or inserted into the holes in the matrix. A well laid out, generously spaced coal layout will give the best results. When lit the flames should not be hitting the sides of the firebox, if so adjust as necessary. No coals should be directly above a flame port.
How do I know what size fireplace insert I need?
The key factor in selecting the size is based on the opening of the existing fireplace. To determine the right size, measure the following: opening height; opening width; opening depth (top and bottom); rear width and the depth of the hearth (area in front of fireplace).
What size BTU gas logs do I need?
The formula for calculating the maximum BTU allowed is: Room Width x Room Length x Ceiling Height x 20. You can use this tool below to perform the calculation. Find out why it is important to limit the BTU output of ventless gas logs based on the size of the room!Dec 11, 2009.
How do you measure a fireplace?
To calculate fireplace size, measure the width, length, and height of your room in inches. Multiply these three numbers together to determine the room’s volume, then multiply that number by four, which will give you a close minimum heat output. You can select an appropriate size with the original dimensions.
What are the dimensions of a gas fireplace?
Standard Gas Fireplace Dimensions Gas fireplaces can be anywhere from 20 inches to 60 inches, but the size of the gas fireplace you choose will ultimately depend on the area of the room and the height of the wall you plan to put it in.
How do I choose gas logs?
Determine The Size Of Your Gas Logs Measure the front width of you fireplace. Measure the width at the back of your fireplace. Measure the depth from the front to the back of your fireplace. Measure the height from the top to bottom of the front your fireplace.
Can I use gas fireplace with wood logs?
The answer to “Can you burn wood in a gas fireplace?” is a resounding NO! That is, if your setup is a true gas-only fireplace. In this type of installation, burning wood is extremely hazardous. With other kinds of gas fireplaces, you might be able to burn wood, but only under the right conditions.
Do you put logs in a gas fireplace?
Pro tip: Burning Wood Logs in a Gas Fireplace Answer? Definitely not. Wood-burning units are meant to hold wood, while gas-fueled units are meant to host gas. Mixing fuel types could lead to fire hazards, smoke back-up, and a lot of damage to your home/unit.
What logs go in a gas fireplace?
The three main types of gas log materials are refractory cement, ceramic fiber and refractory ceramic. Each are designed to be as realistic-looking as possible, but there are several differences to consider when choosing a gas log set for your fireplace. Refractory cement gas logs are formed from a cement mixture.
How do you place rocks in a gas fireplace?
To place the rock wool, grab some tongs and carefully pull small pieces out of the bucket and onto your vermiculite. Your gas logs will lay on your burner pan, so make sure to have the rock wool almost hanging off the edges. This will ensure you can see more “coals” when your fire is burning.
Can I change the coals on my gas fire?
Well surprisingly yes. On some gas fires, you can indeed change the fuel bed effect. The new Icona hole in the wall fires has a variety of different effects including fuel beds, logs, driftwood, coals and pebbles.
Do you need to replace gas fire coals?
Sometimes it’s necessary to change gas fire coals, ceramic logs or pebbles as they become discoloured or worn. Gas fire manufacturers will normally insist on their specific brand of coals to be used on their gas fires claiming it is unsafe or reduces the heat efficiency of the fire.
What causes soot on gas fire coals?
Soot buildup is commonly caused by clogged burner ports and improperly positioned fire-logs. A fire-log that’s out of position can obstruct the flame path that ensures the clean-burning of gas. This contributes to soot formation on the fireplace. Another primary cause of soot is clogged gas burner ports.
Are fireplace inserts standard size?
Fireplace Insert Sizes Fireplace inserts are not one-size-fits-all. They must be the right dimensions for your particular space, so measure the height, width and depth of your fireplace from the back wall to the front opening. The larger the room, the more heat you’ll want it the fireplace insert to produce.
Are fireplaces a standard size?
The standard size of a fireplace is anywhere from 2 – 3 feet wide, 24 – 29 inches high, and always about 16 inches deep. Of course, the opening could vary depending on your style and design ideas, as well as where you are locating the fireplace.
