Table of Contents
If applied correctly, Water Seal will last up to 4 years.
How often does Thompson’s water Seal need to be applied?
Thompson’s WaterSeal includes a complete line of deck sealers and stains for protecting deck wood from moisture and sunlight. Applying a sealer and/or stain typically is recommended every one to three years, depending on the finishing product, deck use, weather conditions, and sun exposure.
How long can Thompson water Seal be stored?
PVC primer and Thompson’s Water Seal™, sealed tightly, can be kept indefinitely (no minimum temperature), as can concrete bonding additive if stored above freezing.
Will Thompsons water Seal protect untreated wood?
The Thompson’s® WaterSeal® cleaner line has a product for every exterior wood cleaning need. Q: Does pressure-treated lumber really need waterproofing protection? Yes. In fact, the chemical treatment actually causes the lumber to dry out quicker and absorb more water than untreated lumber.
Can you use too much Thompson water Seal?
If over-application occurs and there is puddling of the product, redistribute product within 15 minutes to a dry area or wipe off. Q: Will the formula of Thompson’s® WaterSeal® Sport Seal® or Fabric Seal change the feel of the treated surface? No. These products will not change the surface’s feel or leave it sticky.
Is Thompson water Seal any good?
– Thompson’s® WaterSeal® Clear did not alter or change the appearance of the wood. After full drying, we tested the ability to repel water. Water did bead on top of the finish and did not absorb into the wood. – As far as we can tell, Thompson’s® WaterSeal® does not prevent UV graying at all.
How many coats of Thompson’s water Seal do I need?
One coat is enough, but if more color is desired, a second coat can be applied within two hours before the first coat has dried. With Thompson’s® WaterSeal® Waterproofing Stains, you can clean your tools with soap and water.
Does it hurt Thompson water Seal to freeze?
Most stains will be fine because freezing doesn’t affect color. Some of the dyes will coagulate. The best advice don’t let water finishes freeze. Once frozen, most water based finishes such as General Finishes High Performance Water Base Topcoat are no longer useable.
Does Thompsons water Seal need to be shaken?
Shake contents well before use. Shake or mix thoroughly before and occasionally during use. Only one light coat is necessary in most applications. Apply by brush, roller, dipping, or sprayer.
Can you freeze Thompson water Seal?
Do not use in below grade application where water pressure is a problem, or on painted or recently stained surfaces. Protect product from freezing. Do not store below 32°F. In case of accidental freezing, call The Thompson’s Company Help Line.
Should I use Thompson water Seal on pressure treated wood?
Although the wood is resistant to rot and insect attacks because of the pressure treatment, it can warp, split and develop mildew if not protected from the effects of water. The directions for some, such as Thompson’s Water Seal, specify pressure-treated wood as a suitable use.
How do you keep untreated wood from rotting?
Even though natural weather-resistant wood is the best choice for outdoor exposure, at some point it becomes vulnerable to decay. The only way to properly use untreated wood of any type outside is with the addition of water-repellent preservatives, sealer or paint that contain UV protection.
Can you pressure treat wood yourself?
A very safe process does exist to treat lumber, so it’s not so tasty to bothersome insects and wood-destroying fungi – although it’s rapidly being forgotten. You simply soak the lumber in the borate solution. Most people just build a trough using 6-mil plastic sheeting.
How do I remove excess Thompson’s water Seal?
When coatings like thompson’s water seal are applied to heavy, they lay on the surface and have a hard time drying. I suppose it might dry eventually but what I’d do would be to take a wet thinner rag and ‘scrub’ up the excess sealer. It should dry in no time after the excess is removed.
How do you remove excess Thompson’s water Seal?
Steps to Remove the Sealant: To use mineral spirits, wipe the spirits over the area with a cloth. Let it sit for a few minutes, then scrub the area with a scrub brush. To use a concentrated degreaser, follow the instructions on the label of your selected product.
How do you remove Thompson’s water Seal from skin?
Soak your hands in warm water for about five minutes. This helps soften the skin and loosen the Seal-It. Dry hands on a towel, then rub a drop of hand lotion over the area with the Seal-It on it. Gently wipe off the lotion to remove the softened Seal-It.
What is the best way to apply Thompson’s Water Seal?
The fastest way to apply is with a pump-up sprayer (using a coarse setting), but you can also apply with a brush or a roller. You should apply liberally. In the case of areas with heavy discoloration or dirt, apply a second coat, brush lightly with a broom and hose off.
What is the best wood sealer on the market?
Best Outdoor Wood Sealers in September, 2021 Wood sealer Covers (quart) 1 Thompsons WaterSeal Wood Protector 100 sq ft 2 Rainguard Sealer up to 50 sq ft 3 Agra Life Lumber-Seal up to 150 sq ft 4 DEFY Crystal Clear Sealer 50 – 75 sq ft.
What is the best sealant for pressure treated wood?
Best Deck Sealers for Pressure-treated Wood Ready Seal 520 Exterior Stain and Sealer for Wood. SEAL-ONCE Nano+Poly Ready Mix Penetrating Wood Sealer. #1 Deck Premium Semi-Transparent Wood Stain for Decks. Thompsons Waterseal Solid Waterproofing Stain. Eco Advance Wood Siloxane Waterproofer Concentrate.
How many coats of water seal do I need?
Apply 2 coats using brush,roller or sprayer. note: Use at full strength.do not dilute. The second coat should be applied when the first coat has soaked in the surface. For best results do not leave the first coat to dry for more than 1 hour before applying the second coat.
How much does Thompson’s water Seal Cover per gallon?
That determines how many gallons of stain are required (each gallon covers up to 400 square feet).
