Table of Contents
Allow at least 48 hours to dry; however drying time will vary depending on the substrate, temperature, and humidity. Allow minimum of 30 days drying time before applying oil based paint over Thompson’s® WaterSeal® Waterproofing Wood Protector – Clear.
How do you make Thompson Water Seal dry faster?
How to Fix Thompson Water Seal Problems Remove the excess product as soon as you notice it. Give your project more drying time—up to a week. Use a fan to speed up the sealant’s drying process. Keep the coats thin regardless of which Thompson’s product you have. Use a sprayer to apply the sealant whenever you can.
How many coats of Thompson’s water Seal do I need?
One coat is enough, but if more color is desired, a second coat can be applied within two hours before the first coat has dried. With Thompson’s® WaterSeal® Waterproofing Stains, you can clean your tools with soap and water.
Does Thompson Water Seal dry?
DRYING TIME Thompson’s Water Seal should be dry in 2 hours under normal conditions. Dry times depend on the texture & type of surface you’re coating. Remove as much product as possible from equipment before cleaning. All equipment should be cleaned immediately after use with detergent and warm water.
Can you put two coats of Thompson Water Seal on?
Thompson’s WaterSeal products typically need only one application, but you can apply a second coat of stain to darken the wood, if desired. However, you must wait for the first coat to dry (typically about 2 hours) and apply the second coat within 4 hours of applying the first coat.
How long does Thompson’s water Seal last?
Water Seal can only be used on bare and uncoated brick, stone or concrete. How long will Water Seal last? If applied correctly, Water Seal will last up to 4 years. This is dependent on conditions such as orientation of the wall and local climate.
Should I use Thompson water seal on pressure treated wood?
Although the wood is resistant to rot and insect attacks because of the pressure treatment, it can warp, split and develop mildew if not protected from the effects of water. The directions for some, such as Thompson’s Water Seal, specify pressure-treated wood as a suitable use.
Can Thompson water seal go over stain?
Yes, you can put Thompson water sealer over stained wood whether the stain is water or oil-based. If the stain has completely dried and cured it’s fine to apply sealer, but if there is still some moisture, applying the water seal over the stain might cause problems.
Can I stain over Thompson water seal?
The waterproofing nature of Thompson’s precludes using a water based product as a stain or paint. Recoat over the Thompson’s Clear product the following season with a 100% oil and petrochemical based product, clear or stained, such as TWP, Armstrong-Clark, Penofin (Penetrating Oil Finish).
Is Thompson’s water seal oil based or water based?
Thompson’s® WaterSeal® Penetrating Timber Oil is an oil-based product that provides protection by penetrating into wood pores and sealing out water infiltration. Thompson’s® WaterSeal® Waterproofing Stains are water-based products that have film-forming properties to protect the wood by repelling water.
Why is my deck sticky after sealing?
“A sticky or tacky deck is usually due to over-application or failing to wipe the excess stain from the surface of the wood. Rinse thoroughly with a garden hose and spray nozzle, and let the wood dry. This removes any tackiness or residue.”Aug 31, 2011.
Is Thompson’s water seal clear or milky?
Product will appear milky white during application, but will dry clear. If puddling of product occurs, remove within 15 minutes by redistributing to dry areas or wiping off. Tackiness will result if over-applied.
How many square feet does 5 gallons of Thompson’s water seal cover?
That determines how many gallons of stain are required (each gallon covers up to 400 square feet).
How Much Thompson water seal do I need for my fence?
Divide the total square feet of fence to be stained by the coverage listed on the can. For example, if you have 1,000 square feet of fence and the stain says that 1 gallon covers 200 square feet, you would divide 1,000 by 200, which equals 5 gallons to cover the fence.
When can you seal a new deck?
DO wait 30 days before sealing a new deck. But preservatives in the wood often require about 30 days’ dwell time before the deck can soak up the sealant. After a 30-day period, pour some water on your deck. If it beads up, the wood is still too wet to seal, but if the water is absorbed, it’s ready to seal.
Can you spray Thompson’s water Seal with a pump sprayer?
Can you spray thompson’s water seal? Yes, you can apply your Thompson’s water seal using a standard pump garden sprayer and achieve the desired results. This sprayer is best to use when applying sealers.
Does Thompson Water Seal prevent mold?
Thompson’s® WaterSeal® Waterproofer Plus Clear Wood Protector is designed for all exterior wood and decking surfaces. This protection includes: Water repellency, prevents water damage, maintains natural wood grain, all while resisting mold growth.
Can you apply Thompson’s water Seal with a roller?
Q: What is the best way to apply Thompson’s® WaterSeal® cleaners? The fastest way to apply is with a pump-up sprayer (using a coarse setting), but you can also apply with a brush or a roller. You should apply liberally.
Can you use Thompson water seal on pavers?
Provides proven waterproofing protection for all masonry surfaces including pavers, brick, concrete, stone, stucco, clay and quarry tile. Use for concrete waterproofing and as a brick sealer.
How do you remove Thompson water seal from wood?
So here is the only recipe that worked for me Remove the product with a real wood striper, i used “Super remover” this product can dissolve about anything, wear gloves and glasses. Use a green abrasive pad with “Super remover” and scrub the surface. Sand the surface.
