Table of Contents
Allow at least 24 hours to dry; however drying time will vary depending on the substrate, temperature, and humidity. When completely dry, perform the splash test to determine if second coat is necessary. Allow 45 days drying time before applying latex paint over Thompson’s® WaterSeal® Clear Multi-Surface Waterproofer.
How long does Thompson water Seal take to dry before rain?
For deck stain, the deck surface and air temperature should be between 50 and 95 Fahrenheit for application and drying. The forecast should indicate no rain for at least 24 hours after application. The deck surface should be allowed to dry for at least 48 hours before application.
How long after applying Thompson water Seal can you walk on it?
Now that you’ve applied Thompson’s Water Seal following the instructions above, to your entire surface, you can walk away and let it dry for 24 hours. That’s all the time you need to let Thompson’s Water Seal work to protect your outdoor surfaces from water damage.
Does Thompson’s water Seal dry?
No. Thompson’s® WaterSeal® Clear Multi-Surface Waterproofer applies white but dries clear and allows your wood to gray naturally over time. Prior to covering the entire surface, a test patch should be done in an inconspicuous place.
How long does Thompson water Seal last?
If applied correctly, Water Seal will last up to 4 years. This is dependent on conditions such as orientation of the wall and local climate.
Why is Thompson water Seal not drying?
In many cases, high levels of moisture in the air (or worse, rain) may cause the water seal to take longer to dry. Applying water sealant on wet wood or during a moment of very high humidity will not weaken the sealant, though. After two to three days, you probably won’t have any stickiness left on your wood.
How many coats of Thompson water Seal do I need?
One coat is enough, but if more color is desired, a second coat can be applied within two hours before the first coat has dried. With Thompson’s® WaterSeal® Waterproofing Stains, you can clean your tools with soap and water.
Is Thompson water Seal any good?
– Thompson’s® WaterSeal® Clear did not alter or change the appearance of the wood. After full drying, we tested the ability to repel water. Water did bead on top of the finish and did not absorb into the wood. – As far as we can tell, Thompson’s® WaterSeal® does not prevent UV graying at all.
What is the best way to apply Thompson’s water sealer?
The fastest way to apply is with a pump-up sprayer (using a coarse setting), but you can also apply with a brush or a roller. You should apply liberally. In the case of areas with heavy discoloration or dirt, apply a second coat, brush lightly with a broom and hose off.
What temperature do you apply Thompson’s water Seal?
Be sure that both surface and air temperatures are above 50°F during application and remain above 40°F for 48 hours after application. Do not apply product if rain is forecasted within 24 hours of application.
What happens if it rains after sealing deck?
Rain will damage the finish of any wet sealer with linseed oil or mineral oil in it. Because it forms a coating, it takes several hours to dry, and during that time, the sealer is vulnerable. After the rain has passed and the deck has dried, take a closer look.
Can I apply Thompson’s water Seal with a sprayer?
Answer: The manufacturer of Thompson Water Seal recommended that you use their product with a plastic sprayer with a brass wand, such as our Chapin Premier sprayer. Once you are done with the product, it is recommended that you run mineral spirits through the sprayer and then water to clean it.
How do you clean a brush after using Thompson’s water Seal?
After waiting the recommended time, use a synthetic, stiff bristled brush to scrub the surface. Then use a garden hose or pressure washer to rinse away the residue.
Is it better to stain or seal a deck?
Sealing a deck is best for cedar, teak, mahogany, or other quality woods as it enhances the wood grain and natural color. Staining a deck protects the wood from mold, mildew, moisture, and rot, and UV rays and sun damage.
Should I use Thompson Water Seal on pressure treated wood?
Although the wood is resistant to rot and insect attacks because of the pressure treatment, it can warp, split and develop mildew if not protected from the effects of water. The directions for some, such as Thompson’s Water Seal, specify pressure-treated wood as a suitable use.
Why is my concrete sealer sticky?
Is there something I can do to get the stickiness off? A. Too much stain residue remaining on the surface when sealing is the most common cause of sealer failure on stained concrete floors. Stripping the sealer where it is tacky, neutralizing and cleaning the floor, then re-sealing should correct the problem.
What is the best wood sealer on the market?
Best Outdoor Wood Sealers in September, 2021 Wood sealer Covers (quart) 1 Thompsons WaterSeal Wood Protector 100 sq ft 2 Rainguard Sealer up to 50 sq ft 3 Agra Life Lumber-Seal up to 150 sq ft 4 DEFY Crystal Clear Sealer 50 – 75 sq ft.
How many coats of water seal do I need?
Apply 2 coats using brush,roller or sprayer. note: Use at full strength.do not dilute. The second coat should be applied when the first coat has soaked in the surface. For best results do not leave the first coat to dry for more than 1 hour before applying the second coat.
Does Thompson Water Seal need to be shaken?
Shake contents well before use. Shake or mix thoroughly before and occasionally during use. Only one light coat is necessary in most applications. Apply by brush, roller, dipping, or sprayer.
How much does Thompson’s Water Seal Cover per gallon?
That determines how many gallons of stain are required (each gallon covers up to 400 square feet).
What is the longest lasting deck stain?
Solid. Just like regular paint, solid stains hide the grain of wood, and the best should last three to five years on a deck, the longest of the three types of stains.
What does Thompson Water Seal do?
Thompson’s® WaterSeal® Penetrating Timber Oil is an oil-based product that provides protection by penetrating into wood pores and sealing out water infiltration. Thompson’s® WaterSeal® Waterproofing Stains are water-based products that have film-forming properties to protect the wood by repelling water.
Is it better to spray or brush stain?
4. When using a roller or airless sprayer, ALWAYS back brush the stain to really work it into the wood grain. Spraying is a great application (just be extremely cautious of overspray), but the magic is in back brushing it into the wood.
What removes Thompson Water Seal?
Steps to Remove the Sealant: To use mineral spirits, wipe the spirits over the area with a cloth. Let it sit for a few minutes, then scrub the area with a scrub brush. To use a concentrated degreaser, follow the instructions on the label of your selected product.
Is Thompson Water Seal milky white?
Thompson’s Water Seal Advanced Natural Wood Protector goes on milky but dries clear.
