Table of Contents
But expansion tanks can wear out. The average life of your tank can be anywhere between five and 10 years. You can extend the life of your expansion tank by making sure that your home’s water pressure matches the air pressure in your expansion tank. But in some cases, you’ll need to replace it.
What happens when an expansion tank fails?
Oftenthe diaphragm dividing the two systems will fail, causing the two systems to become one. When this happens, the expansion tank turns into a “dead leg” that will eventually cause damage and premature failure to your water heater.
How do you know if your expansion tank is bad?
If it makes a dull thud rather than a hollow sound, your tank is full of water and needs repair or replacement. You can also gauge this by feeling the tank, which will be cool where it’s holding air and warm where it’s holding water. If more than half the tank is warm, you have a problem.
How much does it cost to replace an expansion tank?
The job of the thermal expansion tank is to absorb the extra water volume so that the excess pressure does not cause undue wear and tear on the water heater and other fixtures in the home. The cost to install a new Thermal expansion tank can range from $279 to $443.
How often should expansion tank be replaced?
Between five and 10 years is the average lifespan of your tank. If your home’s water pressure matches the air pressure in your expansion tank, you can extend the life of your tank.
How often do expansion tanks fail?
An expansion tank can fail within the first two years if not calibrated properly. In order to calibrate a thermal expansion tank you must have a water pressure gauge and air pressure gauge. The expansion tank pressure must be equal to your water pressure or it will fail quickly.
Do expansion tanks need to be drained?
Draining the expansion tank should be done periodically, usually once or twice a year. We recommend doing this maintenance before the cool season so you don’t have to work with hot water and risk getting burned. Turn off the boiler and close the water supply valve. Allow the tank to cool if necessary.
Why does my expansion tank keep failing?
The most common expansion tank problem in a diaphragm tank is losing small amounts of air through the valve. When this occurs, more air needs to be added to the tank. If the tank does not hold its air pressure after you complete this fix or it fills with excess water, you may need to replace the diaphragm.
Can an expansion tank explode?
In fact, the tank may explode! Thermal Expansion Can Cause Hot Water Heaters to Explode! A typical hot water heater in an “open” sys- tem has only a temperature and pressure (T&P) valve to prevent a rupture of the hot water heater (figure A). Open systems allow expanding hot water to push into the cold water line.
Why would an expansion tank leak?
And sometimes, as water expands after being heated, it outgrows the space within the tank. When this happens, excess water is immediately sent to the expansion tank to lower pressure levels inside the water heater. But sometimes, due to wear and tear, your expansion tank may start leaking.
Is an expansion tank necessary on a water heater?
While expansion tanks are required by code in most closed-loop water heater systems, they have a reputation for failing. Common expansion tank issues include: Rubber Diaphragm Wear Out.
How much does it cost to install a water heater expansion tank?
$145 – $350, Installed The cost to install a water heater expansion tank ranges from $55 and up for the rare DIY project, to about $350 when a pro adds an expansion tank to a large residential water heater.
Can a bad expansion tank cause high water pressure?
The most common source of high water pressure is actually the municipal water supplier. It’s also possible that you have a faulty expansion tank on your water heater. At the end of the day, the cause of high water pressure is usually something outside of your control.
Will a bad expansion tank cause low water pressure?
Before installing an expansion tank, measure the tank’s air pressure charge. When taken from the box, the air pressure in the expansion tanks will likely be lower than your home’s water pressure.
What happens if expansion tank is full?
Pre-charge pressure that’s too low may be indicated when the tank is full of water. Low pressure can cause too much water from entering the tank. It could also indicate that the diaphragm is no longer functional, which means that there is nothing to prevent the water from entering.
