Table of Contents
There should be a maximum of ½” (1.27cm) slope in an 8′ (2.44m) run. Do not use shims to level the spa, this could create tension on the spa shell which might result in damaging your spa. Because your spa pad must provide continuous support for the entire base of the spa, you should never level it with shims.
Can a hot tub be slightly unlevel?
Leveling a hot tub that is on uneven concrete can be done with simple shims if the slope is less than one inch. But if your hot tub is situated over an existing concrete surface, you may find that the concrete is somewhat unlevel to account for drainage or from poor construction.
Does a hot tub need to be exactly level?
Once a hot tub has been filled with water and bathers, it can weigh over 8,000 pounds. Any surface dips can create stress on the hot tub shell, which can lead to cracking. When leveling a hot tub, it is important to ensure that the surface is completely flat but also that water drainage can easily occur.
How much slope is OK for hot tub?
The spa pad should be at least the size of the spa. If you are going to pour cement pad put a slight slope in it so that water won’t pool under the spa. A 3/4″ slope in a 10 foot wide cement pad is adequate.
What happens if your hot tub is not level?
Over time a spa being unlevel can cause stress to the acrylic and cabinet. As was said, a 1/2 inch total or 1/2 inch in 18 inches is a big difference. If something happens down the road to the shell or cabinet, and it is found that the tub was not level, they may not honor the warranty.
How do you level the ground for a hot tub?
Place a layer of gravel on the leveled spot. The thickness of the layer will depend on the size and weight of your hot tub, but a layer four to six inches thick should be adequate for most hot tubs. Extend the gravel out around the tub in all directions, to avoid having a muddy area around your hot tub.
What is a spa leveler?
The Spa Level-R™ is a solid, secure base used to level your hot tub. It elevates your hot tub off the ground to encourage proper water run-off which will: Protect the hot tub base from wood rot damage. Eliminate green mildew stains on your concrete.
How do you make a level pad for a hot tub?
Concrete Pad Remove all the grass and dig down at least 6 – 8 inches to prepare the base for your concrete spa pad. layer with crush stone and wire mesh to keep the concrete from shifting or cracking. Pour your concrete and finish level for your hot tub water line to be level when in place.
What is the best base to put a hot tub on?
A concrete surface is an excellent base for your hot tub as this material is extremely sturdy and long-lasting. If you have an existing patio made of concrete bricks, make sure it’s in good condition and is level (not angled for drainage). A customized poured concrete pad is an even better choice.
How much clearance do you need for a hot tub?
Space. There must be enough room not just for movement or getting in and out of your tub, but also for maintenance. You’ll need to choose a location that allows for easy access to the inner workings of the hot tub. We recommend leaving at least 30 inches around all sides and back panels of the hot tub.
Can you put a hot tub on pavers?
A hot tub can be placed on pavers, but ensure that they can bear the weight of the hot tub, including water and persons. Ensure that the floor is level and solid. Most pavers are laid at an angle to improve rainwater removal. Such a slope is not suited for a hot tub.
How long should concrete cure before putting a hot tub on it?
They said one week is the MINIMUM; they said it takes up to 28 days for the concrete to completely cure, so they recommend 28 days before putting something really heavy (like a hot tub) on it.
Can you put a hot tub on stamped concrete?
Reinforced concrete at least 4 inches thick, that will support a weight of at least 115 lbs. Make sure the concrete is fully cured before placing the hot tub. Also consider decorative stamped concrete. This can be a very attractive addition.
Can you shim a master spa?
A swim spa by Master Spas needs a solid, level surface that can handle the weight of the swim spa. Master Spas recommends that the foundation is a reinforced concrete pad that is at least 4 inches thick. Do not try to “shim” your swim spa by placing objects underneath to make it level.
Can you put a hot tub on dirt?
A hot tub should not be placed on soil or on a lawn. Instead, it will need a solid platform to support all of the weight. Exposure to wet soil and grass will reduce the life of your hot tub and expose it to insects and moisture. A hot tub should never be installed in soil or on a lawn.
Can you put a hot tub directly on the ground?
Outdoor hot tub placement, such as decks, concrete or brick patios, is common. However, the hot tub can be placed on any solid, uniform, level surface. Do not place your hot tub on grass or bare ground.
Do you have to put a hot tub on concrete?
A hot tub requires a stable surface — whether it’s a concrete slab, reinforced deck, or firmly compacted soil with crushed gravel. There’s also the option to have the hot tub installed in the ground but that still requires a concrete vault.
Do you need a flat surface for a hot tub?
Other Bases As a general rule, as long as drainage is good, the surface is relativley flat, solid and will take the weight of a full hot tub then it should be absolutley fine. Here are a few examples of other foundations that we have placed our hot tubs on just to give you an idea of how many options there are!Mar 27, 2021.
How flat does a hot tub base need to be?
How level does a hot tub need to be? If your spa’s pad is slightly sloped, it will not affect the performance of the spa or its structure; however, there should be no dips, sags, or unevenness in the pad. Most patios are built to slope away from the house for drainage purposes.
