Table of Contents
Measuring of plasticity is based on the principle of impact deformation using a sample with a defined diameter and height deformed by a free falling plate with a given mass. It is defined as the ratio between the water responsible of tile contraction and the total water; Bigot curves show this information.
How is plasticity of clay measured?
As with other types of materials, a compression test can be used to evaluate the plasticity of clays. Baran et al. formulated their workability concept for clays using compression tests in cylindrical samples, allowing to determine the optimum amount of moisture for each clay studied.
How is plasticity tested?
Plasticity testing quantifies the boundaries between semi solid and plastic – the Plastic Limit (PL) and plastic and liquid – the Liquid Limit (LL). The Plasticity Index (PI) is a measure of the plasticity of a soil. The PI is the difference between the Liquid Limit and the Plastic Limit (PI = LL – PL).
Is code for Atterberg limits?
STANDARD • IS: 2720 (Part 5) 1985. DEFINITION • Liquid Limit is defined as the water content at which the soil changes from liquid state to plastic state. APPARATUS • Casagrande apparatus confirming to IS: 9259-1979. Grooving tool.
Is plasticity a chart?
A plasticity chart , based on the values of liquid limit (WL) and plasticity index (IP), is provided in ISSCS to aid classification. The ‘A’ line in this chart is expressed as IP = 0.73 (WL – 20). Depending on the point in the chart, fine soils are divided into clays (C), silts (M), or organic soils (O).
How do you prevent clay shrinkage?
Grog is clay which has been fired then ground up. Grog can come in many particle sizes, from fine to coarse. It is used to reduce shrinkage in clay bodies. The best size of grog for most purposes is a 30/80 mesh.
What is a good plasticity index?
In general, the plasticity index depends only on the amount of clay present. It indicates the fineness of the soil and its capacity to change shape without altering its volume. A high PI indicates an excess of clay or colloids in the soil. Its value is zero whenever the PL is greater or equal to the LL.
At what diameter will a soil thread starts to crumble when it reaches the plastic limit?
The plastic limit is when a thread of soil rolled out on a nonporous surface begins to crumble when it reaches 1/8 in in diameter.
Which soil has more plasticity index?
In general, Soils with a high PI tend to be clay, Those with a lower PI tend to be silt, and. Those with a PI near zero tend to have little or no silt or clay (fines) present.
Why is there 25 blows in liquid limit?
The liquid limit is the moisture content at which the groove, formed by a standard tool into the sample of soil taken in the standard cup, closes for 10 mm on being given 25 blows in a standard manner. This is the limiting moisture content at which the cohesive soil passes from liquid state to plastic state.
What does the plastic limit tell you?
Plastic Limit (PL) is the water content at the change from a plastic to a semi-solid state. Shrinkage Limit (SL) is the water content where the further loss of moisture does not cause a decrease in specimen volume.
How do you measure plastic index?
Record the difference between the wet and dry weights as the weight of moisture. Calculate the plastic limit wp by dividing the “weight of moisture” by the “dry weight of sample” and multiply by 100. Plasticity Index (Ip) of a soil is the numerical difference between its Liquid Limit and its Plastic Limit.
How do you calculate clay shrinkage?
Math to find shrinkage; (Dry measurement – fired measurement) divided by Dry measurement X 100 = % shrinkage. EX; 1 (dry) – . 875(fired) divided by 1(dry) X 100 = 12.5% I converted the fraction to decimals (7 divided by 8 = . 875) to make it easier.
What is liquid limit of soil?
Liquid limit is the water content where the soil starts to behave as a liquid. Liquid limit is measured by placing a clay sample in a standard cup and making a separation (groove) using a spatula. The cup is dropped till the separation vanishes. The water content of the soil is obtained from this sample.
What is considered high pi soil?
The larger the PI, the greater the tendency for a soil to shrink or swell. Arguably, and from a numerical perspective, a clay soil with 0 < PI < 20 is considered to have a low swell potential. In contrast, a soil with 35 < PI < 55 is considered to have a high swell potential.
What is a toughness index?
The toughness index is a measure of the shearing strength of the soil at the plastic limit.
What is fired shrinkage?
Fired shrinkage (shrinkage from dry to fired) is a thus comparative indicator of the degree of vitrification. As a clay is fired higher it shrinks more and more to a point of maximum shrinkage (after which swelling occurs as a precursor to melting).
What is use of plasticity chart?
Plasticity chart is a graph between plasticity index (IP) and liquid limit (WL) in percentage which is used for classification of fine-grained soils as per the Indian Standard Soil Classification System(ISSCS).
What is Casagrande plasticity chart?
The Casagrande plasticity chart has been used for more than 70 years to classify fine-grained soils in accordance with the USCS. The majority are classified in the field as SILT, whereas these same soils are classified by the plasticity chart as CLAY.
What is plastic limit?
The plastic limit is the water content at which a soil-water paste changes from a semisolid to a plastic consistency as it is rolled into a 3.175-mm (1/8-inch) diameter thread in a standard test.
Does Clay shrink when fired?
Clay shrinks both in drying and in firing. Different clay bodies shrink at different rates which can be as little as 4%, or as much as 15% for some clay bodies. We also found through out after years of firing that even with the same clay body, shrinkage can vary 1-2% from batch to batch.
What is the water of plasticity?
: water added to dry clay to make it plastic (as for use by a potter)
