Table of Contents
The temperature in the flue pipe of your furnace can run as high as 400 degrees Celsius, which is about 750 degrees Fahrenheit. This temperature is an indication that your furnace is not running at maximum efficiency and you are losing heat up the chimney.
How hot should a furnace exhaust pipe get?
The pipe material temperature value is usually 86 to 100 degree F. The temperature should be taken outside of the furnace cabinet.
Does a furnace exhaust pipe get hot?
It’s normal for your exhaust pipe and the exhaust to feel warm. It’s also normal to see icicles or other icy build-up around the pipe during freezing weather. If your pipe is very hot, call Breedlove Dobbs so we can have an experienced and qualified technician check it out.
How hot does the outside of B vent pipe get?
Type B Vents any appliance that produces flue gasses that exceed 480° F (249° C).
What should my flue temp be?
You need at least 250 F all the way to the top to avoid water condensation and creosote formation. Depending on how tall your flue is and how well insulated what you have may be enough, wasted heat, or not sufficient.
What is the temperature of gas furnace exhaust?
Exhaust and outlet temperatures fuels like natural gas, liquefied petroleum, diesel and more. Appliance type Exhaust Temperature ( o F) ( o C) Gas-fired heating appliance, no draft hood 460 238 Glass melting furnace 1200 – 1600 650 – 870 Oil-fired heating appliance, residential 560 293.
How hot can a furnace get?
A mid-efficiency gas furnace can raise the temperature to 170F, but a high-efficiency model can only raise it to 150F. There are top quality furnaces that can raise it to 200F.
What is furnace flue pipe?
The flue pipe is a duct pipe that vents, or exhausts, gases from inside the home to the outside. A byproduct of combustion contains carbon monoxide and other dangerous compounds.
Is it normal for furnace to be hot to the touch?
Most single stage furnaces should be just uncomfortable to touch on the main trunk just above the main unit. As Heat rise levels can range from 50-70 higher than ambient air temp. Yes, it’s normal.
How hot does double wall vent pipe get?
These pipes only need a 2-inch clearance to combustibles because they remain cool on the outside, while their internal design allows them to withstand temperatures as high as 1,700 or 2,100 degrees Fahrenheit for a limited time.
What temperature does creosote burn at?
In the burning process, wood starts to chemically break down at 500oF, producing volatile gases including creosote. These gases burn at about 1100’F; if that temperature is not roached, the gases will escape up the chimney, resulting in the loss of much of the wood’s energy.
How do you test a furnace vent pipe?
Take a mental note of where they exit the building and head outside. Once outside, look for the intake and exhaust pipes. They should be near where your furnace is on the inside. Normally, they are a set of curved pipes (PVC, CPVC, or ABS) near the foundation, although sometimes they are on or near the roof.
How do you seal a furnace flue pipe?
Using Silicone Caulk Brush away any dirt or dust from the area around the furnace vent that you will be sealing. Cut the tip of a caulk tube with a utility knife. Inject the silicone caulk into the gap between the vent and the side of the house or foundation. Brush the area to be sealed with a stiff bristle brush.
How do you inspect a flue pipe?
How to inspect your flue pipe Remove the flue cap to check for blockages such as debris or birds’ nests. Replace and secure the cap tightly to the end of the flue pipe. Look for signs of blockages by examining the pipe itself – water streaks or rust on the flue pipe may indicate a blockage, causing moisture to back up.
Can my furnace catch on fire?
Yes, a furnace can catch fire. The following are reasons your furnace can catch fire: Your furnace’s air filter is blocked. Your furnace’s gas pressure is too high. There is a crack in your furnace’s heat exchanger.
What would cause a furnace to run hot?
One of the most common and simple causes of an overheating furnace is poor air circulation. The air filter traps dust and other contaminants that can clog your furnace’s ventilation system. As the filter and ventilation system become clogged, airflow is impeded, which makes the furnace work harder and get hotter.
Can a furnace explode?
A furnace explosion is usually the result of ignition and instantaneous combustion of highly flammable gas, vapor, or dust that has accumulated in a boiler. The effect of the force from the explosion is often much greater than the boiler combustion chamber can withstand.
How does double wall vent pipe work?
Type B gas vent uses a double wall of metal pipe for insulation and safety. The inner pipe of reflecting aluminum heats quickly, containing the warm flue gases inside. The airspace between the inner and the outer pipes provides insulation against heat loss to keep the warmer flue gases on the rise.
Can you touch double wall stove pipe?
Double wall black stove pipe has a 6″ from combustibles and isn’t very hot to the touch. Clearances to combustibles can also be reduced with various items such as Pipe Heat Shields.
Does a hot fire remove creosote?
Creosote is a natural byproduct of burning wood in a wood stove or fireplace. One method to loosen crusty or tarry creosote so it flakes off and falls down into the firebox or fireplace is to burn aluminum cans in a very hot fire.
Do potato peels clean chimneys?
Burning the potato peels will not eliminate all soot or creosote buildup, but they will reduce it. A normal and regular chimney cleaning is still needed to keep the fireplace working properly and safely.
What wood causes the most creosote?
In general, hardwoods like oak, ash, and beech are more difficult to ignite, but they last a long time. Softwoods like fir, pine and cedar make more smoke, and therefore more creosote.
