Table of Contents
For shower-only controls, between 36 and 48 inches from the floor is common. Employ your helper to hold the fixture at an estimated height and then see if it’s a comfortable reach for all users.
How high up should a shower faucet be?
Location of Shower Faucet and Head The tub spout will generally be located 4 inches above the rim of the tub. In a shower only unit, the faucet is placed higher at 48 inches off the floor. The shower head normally is located 72 to 80 inches above the finished floor.
Are shower valves standard size?
A height of 28 inches, or 2 feet 4 inches, is standard for valves in bathtub shower units. For shower stalls, install the valve at the standard height of 48 inches, or 4 feet. Install faucets at the same height as the valve, equidistant from the valve.
How high is a shower niche?
Positioning your niche at chest to eye-level is a good standard. This translates to a height of about 48 to 60 inches. Ideally, you’ll want to position your niche to fit between the studs which are usually located 16 inches apart. But many contractors can help you with planning the space for a more custom look.
How far back do you set a shower valve?
wall position, including tile (2-1/16″ [52mm]). The center line of the supply and discharge piping should be a maximum of 2-3/16″ (56mm) and a minimum of 1-7/16″ (37mm) behind the finished wall surface.
Should shower valve be centered?
Re: Correct location of shower head/shower valve All plumbing is typically centered in the space. You’re splitting hairs whether that is inside the curb to the wall or from the shower door glass to the wall.
How do I know if I have a single handle shower valve?
Assess the faucet and determine how many handles it has. If it has two handles, it is a double-handle faucet, which means that the hot and cold water pipes each connect to separate handles. If it has one handle, it is a single-handle faucet. If the faucet has three handles, it is a rare three-handle model.
Are all shower valves universal?
Shower valves are not universal and you cannot mix manufacturers when it comes to trim and rough-in valves. Besides that, one manufacturer will have different valve sizes and types which may also not be universal and interchangeable with each other. Luckily, shower sets are always sold as a complete set.
How high should a niche be above a tub?
The ideal height for a bathtub shower niche sits at chest to eye-level when standing — a height of around 48 to 60 inches, as this height suits most adults. Set aside a 12-by-24 inch space between studs to hold shampoos, rinses, scrubbers and razors.
How high should a soap dish be in the shower?
If it is a dedicated shower you will want to put the soap dish higher on the wall at 48 to 60 inches. This makes it easy to reach when standing.
How much room does a shower valve need?
The shower valve should be 12 inches apart. The next stage of the project will be aided by a small mark at the center of the plates, in line with where you expect the shower valve and faucet to be. On either side of the midpoint, mark 6 inches.
What do you do when your shower valve is deep?
If your shower valve was installed too deep, you may need to purchase a shower valve extension. Signature Hardware carries valve extensions for some rough-ins, but not all. Professional installation should factor in the correct depth behind the wall, with any exterior wall covering included.
How far from Wall should shower head be?
Typically, a wall-mounted or fixed shower head should be about 3 to 4 inches from the wall. If you angle the shower arm at 100 or 120 degrees, you’d have enough space to move around your bathing enclosure without bumping against the wall.
How far should shower head be from floor?
The ideal height range for the shower controls is between 40 to 50 inches above the floor. You can lower the controls slightly if you’re constructing a seated shower. Getting the shower head height right can make a huge difference. It can determine how comfortable the shower is to use.
Can you extend your shower head?
The easiest and most affordable way to raise the height of your shower head is with an adjustable shower arm. This type of shower arm attaches to your existing shower arm pipe, acting as an extension, and then you can attach your existing shower head.
How much space should be between shower valve studs?
Stud Spacing Your goal is to center the shower valve between studs 12 inches apart. A little mark at the midpoint of the plates, in line with where you expect the faucet and shower valve to be, helps for the next stage of this project. Next, mark 6 inches on either side of the midpoint.
Do all plumbing walls need to be 2×6?
All plumbing walls shall be 2 x 6 studs (minimum) in single family dwellings and townhouses. It shall be the plumber’s responsibility to notify the general contractor when 2 x 6 walls are not provided for plumbing, and to have the proper framing installed before proceeding on any further work.
Do I need a rough-in valve?
A Rough Valve is a REQUIRED PART OF EVERY SHOWER. It mixes hot and cold water to create warm water suitable for your shower. Most shower rough-in valves have 4 ports. 2 inlets for the hot and cold water pipes, and two outlets, one for tub spout and one for showerhead.
