Table of Contents
What Is the Standard Shower Head Height? Let’s tackle the most important question right away by pinpointing the standard height for a shower head. According to Hunker, the industry standard for how high a shower head should be is 80 inches.
Where should shower head be placed?
The showerhead should be placed so it directs water toward the body, not the face or hair. A fixed showerhead, roughed in at 72 inches to 78 inches off the floor, is typical in many showers and tub/shower combinations.
How high should you mount a rain shower head?
Wall Or Ceiling Installation When installing, most rainshower heads are installed a little higher than standard showerheads at 80 inches to 84 inches from the shower floor. However, installing the rainshower head about 84 inches from the shower floor is recommended to accommodate taller users.
What is the rough in height for a shower valve?
Shower Valve Height A height of 28 inches, or 2 feet 4 inches, is standard for valves in bathtub shower units. For shower stalls, install the valve at the standard height of 48 inches, or 4 feet. Install faucets at the same height as the valve, equidistant from the valve.
How far from side wall should shower head be?
Typically, a wall-mounted or fixed shower head should be about 3 to 4 inches from the wall. If you angle the shower arm at 100 or 120 degrees, you’d have enough space to move around your bathing enclosure without bumping against the wall.
How close can shower head be to ceiling?
The tallest person using your shower should have at least a foot of clearance (accounting for at minimum a 3-inch shower arm and a head that’s a few inches tall so that the “rain” has some distance to actually fall).
How far out should a shower valve be installed?
Your goal is to center the shower valve between studs 12 inches apart. A little mark at the midpoint of the plates, in line with where you expect the faucet and shower valve to be, helps for the next stage of this project. Next, mark 6 inches on either side of the midpoint.
How far is shower drain from wall?
Discharge hole (vertical): Drain located at floor height; distance is zero. Fixture (side to side buffer): Measured from center of the toilet to either side, minimum. clearance is 15 inches to any wall or other fixture; 18 inches is recommended if the bathroom layout allows for this.
Should the shower door be higher than the shower head?
Shower heads should never be positioned opposite a door or other opening. Exceptions may be made for smaller or low-flow shower heads or shower heads that point straight down at the floor. A glass transom is located above a frameless glass shower door and can be fixed or movable.
Will a shower valve fit in a 2×3 wall?
All tub/shower faucets are designed to fit within a 2×4 framed wall cavity. Most will fit in a 2×3 wall. If the wall cavity is less than that, then only a few faucets will work.
Does a shower drain need to be in the middle?
The shower drain has to be at the lowest point of the shower floor, and so the floor has to slope down toward the drain from all directions. If the drain is in the center of the floor, you’ll have a relatively level space around the drain to stand on.
How deep is a shower drain?
While a shower usually requires a 2-inch drain pipe, the vent pipe must be either 1 1/2 inches or 2 inches depending on local requirements.
What do I do if my shower head is too high?
The easiest and most affordable way to raise the height of your shower head is with an adjustable shower arm. This type of shower arm attaches to your existing shower arm pipe, acting as an extension, and then you can attach your existing shower head.
Should plumbing walls be 2×6?
All plumbing walls shall be 2 x 6 studs (minimum) in single family dwellings and townhouses. It shall be the plumber’s responsibility to notify the general contractor when 2 x 6 walls are not provided for plumbing, and to have the proper framing installed before proceeding on any further work.
Do I need a rough-in valve?
A Rough Valve is a REQUIRED PART OF EVERY SHOWER. It mixes hot and cold water to create warm water suitable for your shower. Most shower rough-in valves have 4 ports. 2 inlets for the hot and cold water pipes, and two outlets, one for tub spout and one for showerhead.
How thick should walls with plumbing be?
The standard thickness for plumbing walls is 6 inches. With plastic pipes, you can get away with the walls being 4 inches thick instead. The thickness of the plumbing wall does depend on the types of pipes in your home. Metal pipes, which are very common pipes to find in older homes, are larger in size.
Where does the drain go in a walk in shower?
Time-saving installation Traditional shower drains are placed in the centre of the shower and sloped in four directions towards the drain. Creating this four-sided slope is considerably more time-consuming and can only be done with small floor tiles.
How far should bathtub drain be from wall?
You will need to cut a hole in the floor at the drain end of the tub to position the tub drain and install it. The hole should be at least 9 inches wide and 12 inches from the wall.
What is the slope for a shower drain?
In a stall shower, the plumbing code requires the floor to be sloped one quarter (1/4) of an inch per foot in order to carry the water effectively to the drain. This slope, according to the TCNA Handbook is called “sloped fill” or commonly known as the pre-slope.
