Table of Contents
GE and Hotpoint Top Load, Front Load and Unitized washers have powerful drain pumps that can pump water vertically as high as 8 feet above the floor. Spacemaker or Space-Saving compact washers can pump up to a height of 5 feet.
How high can a washing machine pump drain water?
Generally, the maximum height is around 39″ (99 cm). Newer washers often have a drain hose permanently attached, which is designed to make drain installation fool proof. The supplied drain hose shows you exactly how high the washer can discharge.
How far can a washing machine pump its waste?
The total distance is about 5 meters around, but I’ve been told the maximum distance of the washing machine waste pipe is 3 meters.
Can a washer drain be too high?
Yes, the drain hose needs to be elevated and it’s always best to do so at a level that’s higher than the washing machine itself. This will prevent possible siphoning. There are also other steps you can take to ensure that you get the best drainage.
How high should a washing machine standpipe be?
Laundry standpipes must be tall enough to extend past the washing machine’s overflow line—typically 30-36” in height, or 18”-30” above the trap.
Does a washing machine drain hose need to be elevated?
Yes, the drain hose should be raised, and it’s always safer to do so higher than the washing machine itself. This would eliminate the possibility of siphoning. You may also take other measures to ensure that you have the best drainage possible.
Can a washing machine drain into 1 1 2 pipe?
Drain and Trap Requirements A 2-inch drain pipe is required for all washing machines. The former requirement of 1 1/2-inch pipe is not enough to handle the fast drainage of modern washers. As with all plumbing fixtures and appliances, a washing machine drain pipe must also contain a P-trap.
How do I extend the water line to my washing machine?
Lengthening the Drain Hose Unhook the existing drain hose from the standpipe, either by disengaging the hose from the curved hose form or pulling out the curved portion of the pipe. Measure the distance to the new washer location and buy a drain hose extension that is long enough to reach.
How far can you extend a washing machine waste pipe?
The longest hose you can get is 2.5m. If this is still too short it might be a case of looking to extend the copper feed to washing machine connector then attach the hose on. This is a job that can be done.
What size pipe should be used for a washing machine drain?
The required size for your washing machine drain pipe is two inches. The drain pipe must also have a P-trap that measures between six and 18 inches above the floor, and then a standpipe that measures between 18 and 30 inches above that.
Can sewage back up into washing machine?
The main sewer drainpipe under your house connects all the drains in your home, such as sinks, tubs, showers, and toilets. Because the washing machine uses so much water, it can cause backups in all of your house’s drains if you have a large clog.
Do you need a double check valve on a washing machine?
outside tap with hand held hose needs a double check valve to prevent possible backflow,washing machines/dish washers each need a single check valve to prevent tainted water being drawn into your mains water tap’s from the rubber hoses. internal taps,shower mixers may need backflow prevention.
What is the minimum height for a washing machine drain?
In order for the drain hose on your Top Load washer to function properly, the drain must be at least 30″ up from the floor and less than 8 feet high. In order for the drain hose on your Front Load washer to function properly, the drain must be at least 24″ up from the floor and less than 8 feet high.
What is the maximum height of a standpipe?
2 Standpipes for automatic clothes washers shall extend a minimum of 30 inches (762 mm) and a maximum of 48 inches (1219 mm) above the finished floor.
How far can a washer be from a vent stack?
It prevents the possibility of a vacuum forming which could affect the water draining from your washing machine. If your washing machine is more than 4 feet from the vent stack, you should install a vent to make sure there’s enough room for the machine to drain properly.
Does a washing machine drain hose need a loop?
Does a washing machine drain hose need a loop? – Quora. No ! It doesn’t you can simply put the drain hose into the elevated pipe this provides a air gap and because it’s elevated the water from the washing machine won’t be being sucked out.
How do you route a washing machine drain hose?
Reach around to the back of the washer with the measuring tape or yard stick. Leave the machine in its current position. Measure the maximum height of the discharge hose, at the arch, from the floor where it terminates into the standpipe in the floor, nearby laundry sink or recessed drain in the wall.
Can I shorten washing machine drain hose?
Sometimes shortening the drain hose of the washing machine is the only way out if it is several times larger than the distance required to connect to the sewer. Simple cutting will make it impossible to use special tips, and twisting will cause delays in the drain.
What is code for washing machine drain?
According to the Universal Plumbing Code, the standard for washing machine drain size is 2 inches. The P-trap should be between 6 and 18 inches high from the floor, while the pipe should be between 18 and 30 inches high from the floor.
Can I use 32mm waste pipe for washing machine?
32mm is perfectly fine for a washing machine, just think of the size of hose that comes attached to the machine itself!Oct 31, 2020.
