Table of Contents
The standard distance from the back wall is 12 inches, or 12-1/2 inches from the center of the flange to the wall framing. Minimum distance in front of the toilet to the facing wall or fixture is 21 inches.
How far should a toilet be from the back wall?
The Distance To Set The Toilet Flange From The Back Wall. You’ll want to set the center of the water closet flange 12 inches from the finished back wall.
How Far From wall is toilet rough in?
The general rule of thumb for clearance from the wall that faces the bowl is 24″ and just about 15″ on each side. The rough-in measurement indicates how much clearance you have and will allow you to select a compatible toilet.
How far should a toilet flange be from the side wall?
Fifteen inches is the minimum distance from the toilet flange to any sidewall or nearby fixture. You can add more space if you want, but 15” is the very minimum. This means the toilet flange should be at least 15” from the vanity, the shower, the tub, and both the back and side walls.
How do you close a toilet to the wall?
Install the Offset Flange Positions the offset flange so that the bent end moves the flange opening closer to the wall. Make sure the back of the offset flange connects snugly with the drainage pipe. Check to make sure that the flange’s opening is sitting flush and even against the bathroom floor.
How do I know if my toilet is a 10 or 12 rough?
If the old toilet is still there, measure from the center of the capped bolts (on the bottom) to the wall (not the baseboard). There should be 24 inches of clearance from the wall facing the bowl and 15 inches on each side as a guideline. If your measurements are between 11.5 and 12.5 inches, it is a 12-inch rough-in.
Should you caulk around a toilet?
Caulk keeps your toilet secure the floor, and avoids any chance of injury or toilet malfunctioning. It’s actually required by the International Plumbing Code to caulk a toilet to the floor, and now knowing the reasoning behind it, why would you not want to?Dec 13, 2021.
How do I measure toilet rough-in?
To measure the rough-in for your toilet, measure from the wall behind to the toilet to the middle of the closet bolt caps on your current toilet. The closet bolts are the bolts holding your toilet to the floor. If you have baseboards or tiling on the wall behind the toilet, do not include those in your measurement.
Does toilet need to be on outside wall?
Chances are if you are asking yourself this question you may have been told by your builder or designer that the toilet needs to be placed against the outside wall. While there are good reasons to do so, it is not always necessary. In fact, many bathroom layouts have the toilet set against an internal wall.
How far away should the toilet be from the vanity?
Toilet placement A toilet should have some elbow room between it and another fixture or vanity. The NKBA’s recommendation is at least 18″. Codes allow a minimum distance of 15″.
How far should toilet flange be above finished floor?
Check the Flange Height With the toilet removed, you can see the toilet flange and measure its height above the floor. The optimum flange height to aim for is 1/4 inch above the finished floor. This typically allows for almost any type of wax ring to be used and still ensure a good seal.
How far can you move a toilet from the stack?
If your waste line has a diameter of 3 inches, you can place the toilet within six feet of your stack. The toilet can also be as far as 10 feet from your stack, if the diameter of the waste line is 4 inches.
Can you move a toilet away from the wall?
Moving the toilet is not a change to be taken lightly. But if needed, it can be accomplished with substantial plumbing work and a great deal of peripheral work, such as opening up a floor or ceiling, rerouting pipes and drain flange, and re-installing the toilet and other fixtures.
Can you replace a 14 inch rough-in toilet with a 12 inch rough-in toilet?
You can, but the back of the toilet tank will be two inches further away from the wall. The “rough-in” dimension refers to the distance from the wall framing (½-⅝″ behind the finished wall surface) to the center of the sewer pipe on the floor. Standard rough-in is 12 inches.
Can you replace a 10-inch rough in toilet with a 12-inch rough in toilet?
The rough-in for your bathroom plumbing should match the rough-in for the toilet. Even if a toilet is designed for a 10-inch rough-in, you can still install it in a space with a 12-inch rough-in.
Why would I want an elongated toilet bowl?
Elongated bowls are also considered more ‘hygienic’ in that the larger surface area of the bowl makes is easier for men and children to use with less mess. The longer bowl size is also a requirement for ADA use, and the longer/wider bowl is generally easier to use for those with mobility issues.
What is rough in?
: to make a rough or unfinished version of (something, such as a design) as the first step in creating the finished version Rough in the lettering on your poster.
