Table of Contents
Asphalt shingles should overhang the exterior edge of the drip edge by ¼ to ¾-inch. Check local building code for drip edge requirements prior to the start of your roofing project.
Should shingles extend past drip edge?
Yes. Shingles should not extend more than 3/4” (19 mm) past the drip edge. If shingles overhang the edge of the roof by more than 3/4” (19 mm), then they are not supported and may crack and break off. In addition, the wind resistance at the roof edge may be compromised.
How far do shingles hangover drip edge?
The edge of the shingles should hang over a roof between an inch and an inch and a half — or between a half inch and three-quarters of an inch if drip edge flashing is installed. Too much overhang and the shingles could blow off in high winds; too little can allow water to seep into rake or fascia boards.
How far should shingles hang over the gutter?
Most shingle manufacturers recommend a 1/4 to 3/8 inch overhang over your eave, which is where your roof ends by your gutter. In many cases, and particularly as home ages and settles, the roof edge at the eave edge can wave in and out by more than this amount.
How much should a starter overhang for shingles?
Whether installed at the eave or the rake, the starter shingles should overhang the edge of the roof by ¼ inch to ¾ inch. Typically, the finish shingles are then installed to align with the edge of the starters.
Does a roof need an overhang?
A roof overhang is an essential part of your roofing system to protect your house. If you are simply adding function and protection, or if you want to incorporate a new style to update the exterior of your home, a new roof overhang is a good idea.
How much overhang should a roof have?
Two feet is the general maximum length for a typical roof overhang. This will protect a roof from most types of damage. Roof overhangs can extend farther than 2 feet, but beyond this length, they begin to lose structural integrity and require external support.
Does drip edge go on before fascia?
The correct placement of a roof drip edge is on top of the roof’s exterior cover directly between the sheathing and the fascia board, which forms a drainage gap between the drip edge and the fascia board. As a result, the drainage improves water flow and protects the roof from potential water damage.
Do shingles go over or under flashing?
Flashing should overlap the roof-covering material, but on asphalt shingle roofs, for aesthetic reasons, the part of the headwall flashing that extends down over asphalt shingles is often covered with a course of shingle tabs.
Should drip edge go over gutter?
It is recommended that gutters are placed under or ‘behind’ the drip edge of your roof. If gutters are installed below the drip edge, water can drip behind the gutter and cause damage to the wood supporting the gutter system.
Does the drip edge go over the felt?
At the side, or gabels, of a roof, the drip edge goes over the roofing felt. At the bottom of the roof, the drip edge goes under the roofing felt.
Should you use drip edge touch fascia?
A metal drip edge will help protect the sheathing under the roof, but if it’s installed too closely to the fascia board, it can still cause water to be drawn into the fascia. The best installation method is to leave a gap between the drip edge and the fascia board, about the width of a finger.
How do you measure a roof for shingles?
How Many Roofing Shingles Do I Need? Measure the length and width of each plane on the roof (including dormers) then multiply length times width. Add the square footage of each of the planes together.
What is roofing drip edge?
Drip edge is metal flashing installed at the edges of the roof to keep water away from your fascia and from getting underneath your roofing components. If your roof doesn’t have drip edge, water gets behind your gutters and rots out both your fascia board and roof decking.
How much should eaves overhang?
Overhangs can vary from a few inches to a few feet depending on preference; however, the suggested width of an overhang is between 12” and 18” for eaves and no more than 8” for rakes. That said, overhangs can extend as far as 2′ without the need for external supports.
What does a roof overhang do?
Purpose. The main purpose of an overhang is to give the house protection against strong winds and heavy rain. Aside from preventing water from running over the edge of the house, snow and other debris are also caught by this extended edge.
What is a roof overhang called?
Soffit: The underside of the eaves, or roof overhang, which can be enclosed or exposed.
How far should drip edge be from fascia?
Drip edge height: 1 5/8″ Drip edge lip extension: 1/2″ Recommended drainage gap: 1/4″ (approx) spaced off of the fascia board.
Where should drip edge be installed?
Drip edge is installed around the whole perimeter of the roof. It is used to hold the underlayments down and create a watertight seal around the edge of the roof. Only the face of the metal is seen and is usually just white one to one and half inch stripe located right under the shingles and above the fascia.
