Table of Contents
For Building a Deck Railing, Deck Frame, or Fence The maximum spacing of 4×4 deck posts should be 6 feet on center, while the maximum spacing of 6×6 deck posts should be 8 feet on center.
How many posts do I need for a 12×16 deck?
A standard deck will need four footings parallel to the house, but they will need to be temporarily braced by 6 inch-by-6 inch posts.
What is code for deck post spacing?
U.S. building code requires support posts for the rail structure to be no further apart than 6 feet on a deck with 4×4′ deck rail posts and no more than 8 feet apart for decks with 6×6′ deck rail posts. Posts should be no further apart than 5.5 feet on stairs.
How far apart do deck railing posts need to be?
The structural integrity of the railing depends heavily on the posts that support the rail structure. These posts should be no farther apart than six feet on the flat deck and no farther apart than 5 1/2 feet on stairs. Your local building department might require closer post spacing for added rail strength.
What is the distance between decking posts?
Ideally the holes need to be about 300mm in diameter at the top and 400mm at the bottom. The gap between the centre of one post and the centre of the next should be a maximum of 1.8m in any given direction – we recommend 1.5m.
How many footings do I need for a 12×12 deck?
For an attached 12 x 12′ deck, you’ll need at least 3 footings, plus at least 2 more if you’re planning on building stairs with it. If your deck will be a different size, it’s easy to figure out how many you’ll need.
How big do deck footings need to be?
FOOTINGS: – Poured concrete footings should be a minimum of 8” wider than the posts (4×4 post – 12” min. width, 6×6 post – 14” min. width), a two level deck or deck with roof – 24”x24”. – The bottom of the footings must be a minimum of 36” below finish grade level.
Should deck posts be 4×4 or 6×6?
Deck posts must be a minimum of 4×4 according to the IRC but many jurisdictions require a 6×6 post as a standard. To avoid code violations, many deck builders choose the 6×6 even if the 4×4 is acceptable.
How far apart can 6×6 posts be?
Post Anchors are made to support a maximum raililng height of 42 inches. The maximum spacing of 4×4 deck posts should be 6 feet on center, while the maximum spacing of 6×6 deck posts should be 8 feet on center.
How high should deck railing posts be?
The International Residential Council (IRC) requires guardrails to be at least 36 inches high, measured from the deck surface to the top of the rail. Commercial decks attached to multifamily buildings need 42 inch high guardrails.
Can I use 4×6 for deck post?
Size of the deck Most professionals will encourage you to consider going with a 6×6 deck post form the outset of the project. Decks that are going to be built higher than just a few feet off the ground will likely need something more substantial than a simple 4×4.
Can I use 4×4 posts for my deck?
In the past, many decks were built with 4×4 support posts (also called structural posts). But these can bow seriously, even if a deck is only 3 feet off the ground. For that reason, we strongly recommend that you use 6x6s instead, even if your building department does not demand them.
When building a deck How far apart should the joists be?
Step 4: Make Sure Your Joists Are Spaced Correctly Deck joist spacing should never exceed 16″ on center (with the exception of MAX deck boards, which allow for maximum 24″ on center). For a more rigid feel, 12″ or less may be preferred.
What is the gap between decking boards UK?
You need an expansion gap of 5-8mm between the boards. If you are going to build your decking next to a house then make sure it’s 150mm below the damp-proof course and that you don’t cover any air bricks. Try to plan your deck to fit only whole boards, to avoid having to awkwardly cut a board lengthways to fill a gap.
How do you calculate deck posts?
Draw a line through the mid-span of the joists. Then find the mid-span of the beam that the post supports, and extend lines from there back to the line at the joist mid-span. Find the area within the lines. To calculate the design load for the post, multiply the tributary area by the combined live and dead loads.
What is the code for building a deck?
MORE BUILDING code topics Thirty-six inches is the most common residential height, but some jurisdictions vary. Guardrails are required once the deck is 30 ″ or more above grade. A 36 ”rail measured from the top of rail to the deck surface is required. California is the one exception where they Require 42 “guards.
Where do you place footings on a deck?
Deck footings have to be placed just right so that the posts they support land in the center of each footing. Pay attention to the framing plans. They might not call out the location of the footings, but they will at least show the centerline of the beam and the spacing of the posts.
Can I use 2×6 for deck frame?
Or are 2x6s to small for deck joists? You can use 2×6 as deck joists if the deck is low enough to the ground as not to require guard railing. When using S-P-F 2×6 deck joists, the span must not be greater than 9’0″ (2.73m) with joists at 16″ o.c. (400mm), and 9’10” (3.01m)with spacing at 12″ (300mm).
