Table of Contents
The standard distance from the back wall is 12 inches, or 12-1/2 inches from the center of the flange to the wall framing. Minimum distance in front of the toilet to the facing wall or fixture is 21 inches.
How far should your toilet be from the wall?
Most codes require at least 15 inches (measured from the center of the toilet) from any side wall or obstruction and not closer than 30 inches center to center to any other sanitary fixture. (The NKBA actually recommends 32 inches.) There should be at least 24 inches of clear space in front of a toilet or bidet.
What is toilet rough-in distance?
Toilet Rough-In Measurements and Standards Start by measuring the rough-in size. This is the distance between the wall behind the toilet and the center of the drainpipe or the bolts that hold the toilet to the floor. It’s best to perform this measurement before you remove the old toilet.
How do I measure toilet rough-in?
To measure the rough-in for your toilet, measure from the wall behind to the toilet to the middle of the closet bolt caps on your current toilet. The closet bolts are the bolts holding your toilet to the floor. If you have baseboards or tiling on the wall behind the toilet, do not include those in your measurement.
Can you replace a 14 inch rough-in toilet with a 12 inch rough-in toilet?
You can, but the back of the toilet tank will be two inches further away from the wall. The “rough-in” dimension refers to the distance from the wall framing (½-⅝″ behind the finished wall surface) to the center of the sewer pipe on the floor. Standard rough-in is 12 inches.
How far should shower drain be from wall?
Discharge hole (vertical): Drain located at floor height; distance is zero. Fixture (side to side buffer): Measured from center of the toilet to either side, minimum. clearance is 15 inches to any wall or other fixture; 18 inches is recommended if the bathroom layout allows for this.
How do I know if my toilet is a 10 or 12 rough?
If the old toilet is still there, measure from the center of the capped bolts (on the bottom) to the wall (not the baseboard). There should be 24 inches of clearance from the wall facing the bowl and 15 inches on each side as a guideline. If your measurements are between 11.5 and 12.5 inches, it is a 12-inch rough-in.
Can you replace a 10-inch rough-in toilet with a 12-inch rough-in toilet?
The rough-in for your bathroom plumbing should match the rough-in for the toilet. Even if a toilet is designed for a 10-inch rough-in, you can still install it in a space with a 12-inch rough-in.
Can you replace a 12-inch rough-in toilet with a 10-inch?
A toilet with a 12-inch rough-in will definitely not fit into a space with a 10-inch rough-in, but a toilet with a 10-inch rough-in actually has extra space in a 12-inch rough-in space.
How do you move a toilet closer to the wall?
Install the Offset Flange Positions the offset flange so that the bent end moves the flange opening closer to the wall. Make sure the back of the offset flange connects snugly with the drainage pipe. Check to make sure that the flange’s opening is sitting flush and even against the bathroom floor.
How many inches does an offset toilet flange move?
The typical offset is 12-inches for most residential toilets. As a result, the toilet had 4-inches behind the tank. It looked like it was trying to participate in the activities of the bathroom rather than sit quietly until needed.
What is rough in?
: to make a rough or unfinished version of (something, such as a design) as the first step in creating the finished version Rough in the lettering on your poster.
How far should bathtub drain be from wall?
You will need to cut a hole in the floor at the drain end of the tub to position the tub drain and install it. The hole should be at least 9 inches wide and 12 inches from the wall.
How far is a linear drain from the wall?
This means the Drain will typically sit 3-5” away from the back wall. It is ideal to take measurements and center the drain on the wall.
How far does a toilet have to be from a shower?
A minimum clearance in front of the toilet of at least 21 inches. This is required for all your bathroom fixtures, including the shower, vanity or sink and bathtub. A minimum distance from the center of the toilet to both side walls of 15 inches.
Are all toilets the same distance from the wall?
The plumber determines the actual distance when he sets the toilet flange in the floor. The standard distance from the back wall is 12 inches, or 12-1/2 inches from the center of the flange to the wall framing. Minimum distance in front of the toilet to the facing wall or fixture is 21 inches.
Why would I want an elongated toilet bowl?
Elongated bowls are also considered more ‘hygienic’ in that the larger surface area of the bowl makes is easier for men and children to use with less mess. The longer bowl size is also a requirement for ADA use, and the longer/wider bowl is generally easier to use for those with mobility issues.
Do toilets have different depths?
Toilets have many standard measurements, including height, width and depth or length. The width is 15 inches, height is just over 18 inches and the depth is 18.9 inches.
