Table of Contents
The Distance To Set The Toilet Flange From The Back Wall. You’ll want to set the center of the water closet flange 12 inches from the finished back wall.
How Far From wall is toilet rough-in?
The general rule of thumb for clearance from the wall that faces the bowl is 24″ and just about 15″ on each side. The rough-in measurement indicates how much clearance you have and will allow you to select a compatible toilet.
Where should a toilet flange be placed?
In a typical toilet installation, the floor flange that sits inside the drain opening below the toilet should be positioned so that its bottom surface rests flush against the finished floor or no more than 1/4 inch above or below the floor.
How do you close a toilet to the wall?
Install the Offset Flange Positions the offset flange so that the bent end moves the flange opening closer to the wall. Make sure the back of the offset flange connects snugly with the drainage pipe. Check to make sure that the flange’s opening is sitting flush and even against the bathroom floor.
How far should toilet flange be above finished floor?
Check the Flange Height With the toilet removed, you can see the toilet flange and measure its height above the floor. The optimum flange height to aim for is 1/4 inch above the finished floor. This typically allows for almost any type of wax ring to be used and still ensure a good seal.
How far should toilet be from side wall?
Most codes require at least 15 inches (measured from the center of the toilet) from any side wall or obstruction and not closer than 30 inches center to center to any other sanitary fixture. (The NKBA actually recommends 32 inches.) There should be at least 24 inches of clear space in front of a toilet or bidet.
How far is toilet drain from wall?
The standard distance from the back wall is 12 inches, or 12-1/2 inches from the center of the flange to the wall framing. Minimum distance in front of the toilet to the facing wall or fixture is 21 inches.
Should a toilet flange sit on top of tile?
The toilet flange needs to be on top of the finished floor. Meaning the bottom edge of the flange needs to be on the same plane as the toilet. So if your toilet sits on the tile, the flange needs to be on top of the tile too. The spacing of the toilet exit “horn” and sealing surface is designed for this height.
How far can you move a toilet from the stack?
If your waste line has a diameter of 3 inches, you can place the toilet within six feet of your stack. The toilet can also be as far as 10 feet from your stack, if the diameter of the waste line is 4 inches.
Does a toilet have to be against a wall?
Toilets should have a minimum of 15 inches from walls that flank the fixture. A distance of 12 to 12.5 inches should be between the center of the toilet flange and the back wall.
What is an offset toilet flange?
Unlike a standard flange, which is centered on the waste pipe, an offset flange is off-center—that lets you shift the location of the toilet by a couple of inches (left, right, forward or back).
Can a toilet flange sit above the floor?
When you install your toilet flange, it should be installed on top of the finished floor, and it should also be installed perfectly level. If your flange sits uneven or below the floor, then it’s wrong. It has to sit evenly on top of the finished floor. As a result, the toilet may wobble or leak at the base.
How do I fill the gap between my toilet and floor?
Apply a thin, even bead of caulk around the base of the toilet to cover the gap along the floor and hide the shims. If necessary, smooth the caulk with your finger, wiping your finger clean frequently with a paper towel or a rag.
How far away should the toilet be from the vanity?
Toilet placement A toilet should have some elbow room between it and another fixture or vanity. The NKBA’s recommendation is at least 18″. Codes allow a minimum distance of 15″.
How much space does a toilet take up?
A standard toilet is from 28 to 30 inches deep, and the waste opening is usually just in front of the tank, so the hole should be roughly 40 inches from the facing wall. You also need room behind the hole for the toilet to fit, which is 12 inches from the center of the hole to the finished wall for a standard toilet.
What is the minimum space for a toilet?
The National Kitchen & Bath Association requires at least 24 inches clearance in front of a toilet. Moreover, the NKBA recommends 32 inches from the center of the toilet waste line to the center of that of any other sanitary fixture, although local codes may require only 30 inches.
Should there be a gap between toilet tank and bowl?
Most toilets have a space between the bottom of the tank and the top of the bowl anywhere from a ¼ of an inch to a ½ inch. Tighten too loosely and the tank will leak underneath the rubber washers and down the bolts; tighten too much and risk the tank cracking.
How far should a soil pipe be from the wall?
Generally, this distance tends to be around 300mm in a cavity wall, so take this measurement and add an extra 300mm onto this figure – this will allow the WC waste connector to be fitted.
How far does an offset toilet flange move?
For the waste water line, an offset toilet flange will allow you to move the toilet a couple of inches in any direction without having to cut a new hole in the floor or reconstruct the waste water pipe.
How close should tile be to toilet flange?
Most toilets have the flange above the flooring, roughly 1/8th to 1/4th of an inch above the tiles.
