Table of Contents
Starting with your perimeter, mark the location of each deck post to locate the fitting position. In general, posts should be spaced no more than 8 feet apart. Some builders position them every 4 feet for a completely rigid frame. The maximum distance between footings is determined by the size of your joist material.
How far apart can 4×4 post for deck?
For Building a Deck Railing, Deck Frame, or Fence The maximum spacing of 4×4 deck posts should be 6 feet on center, while the maximum spacing of 6×6 deck posts should be 8 feet on center.
Should I use 4×4 or 6×6 deck posts?
Unfortunately, a 4×4 post may not be able to withstand the weight, causing the entire porch to buckle. A 6×6 post gives you a little more long-term stability, particularly in those colder climates. Not only does it perform better when carrying heavier loads, but it also makes the heading for your roof more secure.
How many posts do I need for a 12×12 deck?
For an attached 12 x 12′ deck, you’ll need at least 3 footings, plus at least 2 more if you’re planning on building stairs with it.
Are 4×4 posts big enough for a deck?
Deck posts must be a minimum of 4×4 according to the IRC but many jurisdictions require a 6×6 post as a standard. To avoid code violations, many deck builders choose the 6×6 even if the 4×4 is acceptable.
Should deck joists be 2×6 or 2×8?
In general terms, joists spaced 16 inches on center can span 1.5 times in feet their depth in inches. A 2×8 up to 12 feet; 2×10 to 15 feet and 2×12 to 18 feet. The larger the deck, the larger the joists. 2×6 joists should only be used on ground-level decks that do not require, and will not provide for, any guards.
Should you notch deck posts?
Say “No” to notching pressure-treated deck posts. We want you to build an outdoor railing system that you, your family and guests can enjoy without worrying about safety issues. In order to do so, you need to know this building shortcut is not advisable, and we recommend avoiding it at all costs.
What accounts for roughly 90% of all deck collapses?
About 90% of deck collapses occurred as a result of the separation of the deck ledger board from the house, allowing the deck to swing away from the house. It is very rare for deck floor joists to break mid-span. Many more injuries are the result of rail failure, rather than complete deck collapse.
How many footings do I need for a 12×16 deck?
A standard deck will need four footings parallel to the house, but they will need to be temporarily braced by 6 inch-by-6 inch posts. Using doubled boards, you will then need to build beams on the top row of the posts to frame the edges of the deck. These must be topped with adjustable post caps.
How do you calculate deck posts?
Draw a line through the mid-span of the joists. Then find the mid-span of the beam that the post supports, and extend lines from there back to the line at the joist mid-span. Find the area within the lines. To calculate the design load for the post, multiply the tributary area by the combined live and dead loads.
How wide should deck footings be?
FOOTINGS: – Poured concrete footings should be a minimum of 8” wider than the posts (4×4 post – 12” min. width, 6×6 post – 14” min. width), a two level deck or deck with roof – 24”x24”. – The bottom of the footings must be a minimum of 36” below finish grade level.
What is stronger 2×6 or 4×4?
The single 2×6 is 68% stronger than the 4×4 for vertical loads as you describe. However, I caution you that it may be a good idea to have someone design this beam properly so the job is done right. If you’re willing to have a 4″ wide beam, why not create a double 2×6 beam, this will be 237% stronger!Jan 1, 2007.
Is a 4×4 post stronger than 2 2x4s?
When used vertically, 4x4s are stronger than two 2x4s. However, if you need a horizontal surface, two 2x4s will be stronger than one 4×4. A 4×4 should not be used horizontally for anything structural. Always be sure that you’re using the proper size and strength of lumber.
How many posts do I need for a 8×12 deck?
The shorter sides—in this case, the 8-foot side—will have 4-feet of distance between deck posts. The larger 12-foot side will have a post spacing of 6 feet at a minimum code requirement. That makes a total of eight posts that need to be installed on this average size deck.
How far can a 2×6 decking span without support?
2-grade 2×6 joists can span up to 10 feet 9 inches from beam to beam when spaced the standard 16 inches apart with a maximum live load of 30 inches per square foot.
Which way should deck boards run?
On most decks, the decking boards run parallel to the house and across the joists (either perpendicular or at a 45 degree angle).
Can I use 2×4 for deck joists?
The short answer is yes. 2x4s can work for deck joists. However, they aren’t ideal for spanning long distances without bending or breaking, so you have some limitations. Choosing 2x4s for a low-sitting deck is perfect for keeping your feet out of the mud.
Can you use 4×4 posts for a deck?
In the past, many decks were built with 4×4 support posts (also called structural posts). But these can bow seriously, even if a deck is only 3 feet off the ground. For that reason, we strongly recommend that you use 6x6s instead, even if your building department does not demand them.
What is code for deck railing posts?
U.S. building code requires support posts for the rail structure to be no further apart than 6 feet on a deck with 4×4′ deck rail posts and no more than 8 feet apart for decks with 6×6′ deck rail posts. Posts should be no further apart than 5.5 feet on stairs.
