Table of Contents
SPACING FENCE POSTS As chain link fence posts are smaller and sturdier than many other types, the holes should be smaller and can be farther apart. Follow the fence manufacturer’s instructions for spacing, which typically ranges from 4-10′ apart—spacing should not exceed 10′ on-center.
What is a good distance between fence posts?
Typically, fence posts are spaced between six and eight feet apart. The corner posts are set first. To align all of the posts in between, stretch a line from each corner post to work as your guide.
Does chain link fence need tension wire?
Chain Link Tension Wire Installation. Tension wire is an important part of chain link fencing. It secures the bottom and top of your chain link fence to ensure the chain links remain tight to the posts and rails.
How far apart should fence posts be for dogs?
Line posts should be placed about 15 to 20 feet (4.5 to 6 meters) apart. You can use spray paint to mark where to dig the holes for these posts.
Can fence posts be 10 feet apart?
Typical spacing is right around 8 feet between each post however different circumstances may call for different measurements and it is not uncommon to have spacing between posts reach up to 10 feet. Once you have a rough idea of your post layout start by digging your first hole.
How thick should a metal fence post be?
That’s why we choose and recommend heavy duty, contractor grade, 0.095″ inch thick or greater, galvanized steel posts. The metal post above is rated schedule 20, and measures 0.095″ inches thick.
Should fence posts be inside or outside?
Fence posts should be on the outside of the fence The correct installation of ag fencing is to place it on the inside of the posts. This way, animals in the enclosure brush against the wire, not the posts. Fence posts that have been placed outside of the fence material will take nearly all of the animal’s force.
Can you pound in chain link fence posts?
If you decide to install your chain link fence without concrete, use a post-hole digger to make a hole deep enough to bury the posts at least two feet, or about 1/3rd of the height. Never pound the posts into the ground, especially if you have hard clay or rocky soil, because you’ll bend the tops.
Can you use T posts for chain link fence?
Chain link fencing can be installed with T-posts. The chain link goes over them and is attached to the posts. Chain link can also be installed with T-posts. These posts are typically used to install smaller chicken wire and garden fencing, but can be used to install chain link.
How many bags of cement do I need for a fence post?
Most fence post holes will need between 1 – 4 bags of concrete to securely hold the post in place. The best way to determine the size of the hole is: Diameter of the hole is 3 times the width of the fence post.
Should chain link fence touch the ground?
Generally, it is not recommended for a chain-link fence to touch the ground. Ground contact makes the bottom of the fence more vulnerable to corrosion. It can also make yard maintenance more difficult. The fence touching the ground can prevent rodents and other small animals from getting inside for garden areas.
What is the wire at the bottom of a chain link fence?
Galvanized steel tension wire is used to apply tension and secure the chain link fabric along the bottom of your fence in place. The wire is attached to bottom brace band carriage bolt and should run along the same side of the posts as the fabric.
How do you reinforce a chain link fence at the bottom?
The simplest way to reinforce your chain link fence at the bottom is by using tent stakes. Tent stakes can be bought at any hardware store, and they are very cheap. If you don’t want to do any kind of installation or you’re just not the DIY person, then using tent stakes is a simple and straightforward solution.
How deep should a T post be?
T-posts are available in a variety of heights. When it comes to selecting the proper t-post for your project, choose a post that is 24″-36″ taller than your finished fence. That’s because the post will need to be buried at least 2′-2-1/2′ feet deep to prevent weather changes or determined animals from pulling them out.
What is the difference between at post and AU post?
Steel T-posts and U-posts are used exclusively with wire fencing. T-posts are shaped like the letter T, and U-posts are shaped like the letter U. You can get away with a little more distance between posts if using barbed wire.
Is 2 feet deep enough for fence posts?
2 feet is the minimum depth that you should dig your fence post holes for. To dig the holes one-third to one-half of the post’s aboveground height, is a general formula. The deeper you dig the holes, the more stability your fence has.
What size post do you use for an 8 foot fence?
A common rule of thumb, is to dig the hole 3 times as large as the post, and to a depth of 1/3-1/2 of the post height above ground. so for a 8′ high fence, using 4×4 posts. dig the holes 12″ in diameter, to a depth of 2 1/2 – 4′. Of course, that’s assuming you’re setting the posts in concrete.
How do you strengthen metal fence posts?
Fill the hole with approximately 6 inches of gravel. Top the gravel with rapid-set cement mix powder to fill the hole to 3 inches below the surface of the soil. Use the rubber mallet to pound the fence post into place and place the spirit level on top of the post to ensure that it’s level vertically.
How tall should a 6 foot fence be?
As a general rule of thumb, you’ll need to place at least 1/3 the height of the post in the ground. For example, a 6-foot tall fence will need at least 2 feet of post in the ground.
How do I make fence posts all the same height?
Dig a hole at each corner of the area to be fenced by using a post-hole digger or shovel. Make each hole’s width three times the diameter of a fence post, and make each hole’s depth one-third of the post’s height. The bottom one-third of each post will be buried in the ground to provide support.
