Table of Contents
U.S. building code requires support posts for the rail structure to be no further apart than 6 feet on a deck with 4×4′ deck rail posts and no more than 8 feet apart for decks with 6×6′ deck rail posts. Posts should be no further apart than 5.5 feet on stairs.
What is code for railing spacing?
The handrail shall be designed to provide a grasping surface to avoid the person using it from falling. The spacing of brackets shall not exceed 8 feet. (e) Handrails projecting from a wall shall have a space of not less than 1 1/2 inches between the wall and the handrail.
What is the maximum space between railings?
U.S. building codes mandate that balusters have no more than a 4-inch gap between them. This relatively tight amount of spacing still allows for visibility between spindles, but also stands as a safety measure to prevent small children from becoming stuck between spindles or from slipping through the balusters.
How far apart should 4×4 posts be on a deck?
For Building a Deck Railing, Deck Frame, or Fence The maximum spacing of 4×4 deck posts should be 6 feet on center, while the maximum spacing of 6×6 deck posts should be 8 feet on center.
How far apart can newel posts be?
Therefore, if you have a sixteen-foot balcony, you will need three newel posts, one at the beginning, one in the middle, and one at the end. But if the balcony is eighteen feet, then it would require four newel posts as the distance between each post would be greater than eight feet if only three newel posts were used.
What is the code for deck posts?
Beams and girders must be made from laminated two-by-fours, two-by-sixes or two-by-twelves rather than solid lumber, and deck joists can’t cantilever more than 24 inches beyond a support beam or girder. All vertical support posts must be made from six-by-sixes, and posts can be no taller than 14 feet.
Should I use 4×4 or 6×6 deck posts?
Unfortunately, a 4×4 post may not be able to withstand the weight, causing the entire porch to buckle. A 6×6 post gives you a little more long-term stability, particularly in those colder climates. Not only does it perform better when carrying heavier loads, but it also makes the heading for your roof more secure.
How many posts are needed for a 10×10 deck?
A freestanding 10′ x10′ deck needs 4 posts, supporting two pairs of 2-ply non-incised 2×8 beam, upgrading the beam to 3-ply using incised wood.
Should you notch deck railing posts?
Say “No” to notching pressure-treated deck posts. We want you to build an outdoor railing system that you, your family and guests can enjoy without worrying about safety issues. In order to do so, you need to know this building shortcut is not advisable, and we recommend avoiding it at all costs.
Why are newel posts so expensive?
The final feature that causes differences in price are the materials which box newel posts are made from. These may be large pieces of solid wood reducing the number of joints; smaller pieces assembled to make the sides, and finally veneered plywood, or other manufactured wood such as MDF or particle board.
How far apart are porch spindles?
Balusters are the vertical guards that support the handrail. They must be installed close enough that the space between them is less than 4 inches. Most city inspectors carry a 4-inch ball with them to test the spacing. Installed balusters should withstand 50 pounds of pressure exerted over a 1-sq.
Where do you put newel posts?
Balusters and newel posts are all centered along the same baluster line. This is calcu- lated by determining the exact location of all the balus- ters on the stair tread. The edge of each baluster should be 1.5” from the front edge of the stair tread.
Can I use 4×4 posts for my deck?
Deck posts must be a minimum of 4×4 according to the IRC but many jurisdictions require a 6×6 post as a standard. To avoid code violations, many deck builders choose the 6×6 even if the 4×4 is acceptable.
What size are deck support posts?
Deck posts are usually 4 feet x 4 inches, 6 feet x 6 inches or 8 feet x 8 inches as determined to be appropriate for the expected load. After determining the width, the maximum deck post height must also be determined. This also depends on the type of wood used.
Can I use 2×6 for deck joists?
2×6 joists should only be used on ground-level decks that do not require, and will not provide for, any guards. Most decks use 16″ on center spacing for joists. Most decking is not strong enough to support longer spans than 16″.
Should I set my deck posts in concrete?
A deck post should always be placed on top of footing, not inside concrete because it can break. Concrete tends to absorb moisture and wood expands when it gets wet, so these two factors combined will result in the wood breaking the concrete.
What accounts for roughly 90% of all deck collapses?
About 90% of deck collapses occurred as a result of the separation of the deck ledger board from the house, allowing the deck to swing away from the house. It is very rare for deck floor joists to break mid-span. Many more injuries are the result of rail failure, rather than complete deck collapse.
Should you notch a 4×4 post?
While you might expect the notch to be the weak point in the connection, in fact none of the test posts failed at the notch. Even so, notching should be avoided, because it does substantially reduce the strength of the post.
How many support posts do I need for a 12×12 deck?
For an attached 12 x 12′ deck, you’ll need at least 3 footings, plus at least 2 more if you’re planning on building stairs with it.
How do you calculate deck posts?
Draw a line through the mid-span of the joists. Then find the mid-span of the beam that the post supports, and extend lines from there back to the line at the joist mid-span. Find the area within the lines. To calculate the design load for the post, multiply the tributary area by the combined live and dead loads.
