Table of Contents
SPACING FENCE POSTS As chain link fence posts are smaller and sturdier than many other types, the holes should be smaller and can be farther apart. Follow the fence manufacturer’s instructions for spacing, which typically ranges from 4-10′ apart—spacing should not exceed 10′ on-center.
How deep should chain link posts be?
Dig the line post holes – 6 inches diameter and 18 to 24 inches deep with sloping sides (bottom wider than top). The height of line posts, above level ground equals the height of the fabric minus 2 inches. Repeat the terminal post installation steps for each line post.
What is a good distance between fence posts?
Typically, fence posts are spaced between six and eight feet apart. The corner posts are set first. To align all of the posts in between, stretch a line from each corner post to work as your guide.
How far apart should fence posts be for dogs?
Line posts should be placed about 15 to 20 feet (4.5 to 6 meters) apart. You can use spray paint to mark where to dig the holes for these posts.
Can fence posts be 10 feet apart?
Typical spacing is right around 8 feet between each post however different circumstances may call for different measurements and it is not uncommon to have spacing between posts reach up to 10 feet. Once you have a rough idea of your post layout start by digging your first hole.
How thick should a metal fence post be?
That’s why we choose and recommend heavy duty, contractor grade, 0.095″ inch thick or greater, galvanized steel posts. The metal post above is rated schedule 20, and measures 0.095″ inches thick.
Is 2 feet deep enough for fence posts?
2 feet is the minimum depth that you should dig your fence post holes for. To dig the holes one-third to one-half of the post’s aboveground height, is a general formula. The deeper you dig the holes, the more stability your fence has.
How many bags of cement do I need for a fence post?
Most fence post holes will need between 1 – 4 bags of concrete to securely hold the post in place. The best way to determine the size of the hole is: Diameter of the hole is 3 times the width of the fence post.
Do you have to cement chain link fence posts?
You can install a chain link fence without using concrete, but it is not recommended. Anchoring each fence post in concrete is the best way to ensure your fence will stand straight and tall for many years.
Should metal fence posts be set in concrete?
You tend to get a better long-term result by setting the fence posts in concrete as opposed to gravel. When setting fence posts in concrete, it’s best to let the concrete dry for three or four days before attaching your fence rails, panels or pickets.
Does fence go on inside or outside of posts?
Fence posts should be on the outside of the fence The correct installation of ag fencing is to place it on the inside of the posts. This way, animals in the enclosure brush against the wire, not the posts.
How deep should post be driven?
The general rule of thumb when setting a post is that the depth of the post’s hole needs to be one-third to one-half of the actual above-ground height of the post. So, a six-foot-high finished post ideally needs to be buried three feet into the ground.
What size post do you use for an 8 foot fence?
A common rule of thumb, is to dig the hole 3 times as large as the post, and to a depth of 1/3-1/2 of the post height above ground. so for a 8′ high fence, using 4×4 posts. dig the holes 12″ in diameter, to a depth of 2 1/2 – 4′. Of course, that’s assuming you’re setting the posts in concrete.
How do you strengthen metal fence posts?
Fill the hole with approximately 6 inches of gravel. Top the gravel with rapid-set cement mix powder to fill the hole to 3 inches below the surface of the soil. Use the rubber mallet to pound the fence post into place and place the spirit level on top of the post to ensure that it’s level vertically.
How do I make fence posts all the same height?
Dig a hole at each corner of the area to be fenced by using a post-hole digger or shovel. Make each hole’s width three times the diameter of a fence post, and make each hole’s depth one-third of the post’s height. The bottom one-third of each post will be buried in the ground to provide support.
What size post should I use for a 6 foot fence?
A good rule of thumb is to dig a hole 1/3 the depth of the overall post height. A 6′ tall post requires a 2′ hole and an 8′ 4×4. Down in Alabama we sink fence posts a minimum of 2 feet, but the deeper the post is, the sturdier it will be.
What size t post do I need for a 4 ft fence?
When figuring out what size T-post to use for a four-foot fence, remember that you will drive the posts about two feet into the ground. This means you need posts that are at least 24 inches longer than how tall you want your fence. For a four-foot fence, you should use T-posts that are at least six feet long.
How deep should a 5ft fence post be?
Keep the height of your fence in mind when digging your post holes. As a general rule of thumb, you’ll need to place at least 1/3 the height of the post in the ground. For example, a 6-foot tall fence will need at least 2 feet of post in the ground.
What is the best concrete mix for fence posts?
In terms of the ratio to use for a concreting fence posts, the best mix is a mix of 1:2:4 (1 cement, 2 sand, 4 aggregate). Concrete is always best mixed using a cement mixer to ensure it’s even, but if you only need to mix a little, hand mixing is ok (see mixing concrete project above for tips on how to do this).
How much does 2 yards of concrete cost?
According to industry experts, the average cost of concrete in 2020 was $124 per cubic yard, or $248 for the 2 cubic yards needed for a typical 10-by-10-foot patio. *These prices reflect both the average $125 per cubic yard price plus short load fees.
How much does a 50 pound bag of concrete cost?
Compare Similar Products current product Quikrete SAKRETE SAKRETE 50 lb. Fast-Setting Concrete Mix 80 lb. Gray Concrete Mix 50 lb. Fast Set Concrete Mix $498 Buy 64 or more $4.48 $447 Buy 42 or more $3.58 $527 (1710) (1564) (846).
