Table of Contents
A mousetrap powered car is a vehicle that is powered by the energy of a wound-up mouse trap’s spring. Once the drive axle and mouse trap are released the string is pulled from the drive axle by the mouse trap and this causes the drive wheels to rotate.
What makes up the powertrain of a mousetrap car?
Acting as a powertrain that transfers energy from the spring motor to tires are the lever, string, as well as the wheel and axle. On a mousetrap, a spring is connected to a lever. As the spring is released it transfers its torque to the lever.
How do you make a mousetrap car move?
If a mousetrap vehicle is struggling to move and/or needs more acceleration then the lever arms can be shortened in order to increase the pulling force. Keep in mind that you will also have to reposition the mouse trap closer to the drive axle or the system will not work as intended.
What force does a mousetrap car use?
Friction is a force that acts against the motion of all moving objects. Energy is required to overcome friction and keep an object moving. Mousetrap cars start with a limited supply of energy. This energy is used to overcome friction and propel the vehicle.
Why does my mousetrap car turn?
If a mousetrap racer is turning to the left it is because the front axle is pointed slightly left or the distance between the front and rear axles is greater on the right side of the vehicle (see picture bellow). bonus tip: Once the axle holes are in alignment the mousetrap vehicle will travel straight.
How do you make a mousetrap car go the farthest?
Using large rear wheels allow one rotation of the axle to take the car a much further distance. In other words, a given length of the string from the mousetrap moves the car a greater distance. The last note is to place your mousetrap as close to the front of the car as possible.
Should a mousetrap car be heavy or light?
Above all, your car should be light. The smaller the mass of your car, the better — every gram or milligram you can shave off of your car’s frame is a little further your mousetrap will be able to push your car.
How do mousetrap cars reduce friction?
Try to have a minimum gap of 1/8 inch between the frame and any spacers (or wheels) in order to decrease any rubbing friction. Use thrust washers and graphite powder between spacers (or wheels) and the frame to help reduce the rubbing friction.
How long should the lever arm be on a mousetrap car for distance?
For maximum speed, position the mousetrap 2 1/4 inches from the drive axle and cut the lever arm to a length of 4 1/4 inches. The lever arm can be cut using a dremel tool or by using a fine tooth hobby saw. The lever arm should always be “just” long enough to reach the drive axle or performance will be compromised.
Can a mouse trap break your finger?
A mouse trap might not break your finger, but it’ll hurt. Rat traps, though, which are about 4 times larger and stronger than mouse traps and usually have serrated edges, could break your finger. If they don’t break your finger, you could still have severe bruising or pinched nerves.
How long should a mousetrap car be?
The ideal size for an ultra big wheel on a long distance mousetrap racer seams to be somewhere between 10 and 15 inches. And the ideal size for a drive wheel on a speed-trap racer seams to be between 2 and 3 inches but no more than 4 inches.
What is an axle hook on a mousetrap car?
An important part of a mousetrap vehicles propulsion system is the axle hook. If the string does not properly release from the drive axle the string will rewind around the drive axle and cause the mousetrap car to come to an instant stop.
What is the fastest mousetrap car?
The Speed-Trap Racer is the fastest mousetrap powered racer anywhere and was designed after Doc Fizzix’s own record-setting mousetrap racer that traveled 5 meters in 1.2 seconds.
How far did the world record mousetrap car go?
Description: The secret to Doc Fizzix’s world record setting mousetrap distance racer that traveled over 182 meters was it’s unique pulley system. This is the same pulley set-up that was used on Doc Fizzix’s world record setting mousetrap distance car.
Do snap mouse traps work?
Traditionally, snap traps have been popular for killing mice and rats swiftly. If you’re trying to bring down the population of house mice and deer mice in your area, snap traps can work especially well. When used correctly, the quick trigger system of a snap tap can help manage large infestations.
What can you use for wheels on a mousetrap car?
As you might guess, the materials used to build mousetrap-powered cars are light out of necessity. Foamcore board or balsa wood are often used for the body. The wheels can be off-the-shelf radio-controlled car wheels, but many builders use blank CDs or DVDs because their thin edges reduce friction.
What materials do you need for a mousetrap car?
What You Need: Wooden snap-back mousetrap. Duct tape. 4 eye hooks. Wooden dowel that fits inside the eye hooks. Heavy cardboard. Large and small rubber bands. Foam board (usually found at a craft store) String.
Why does a mousetrap car stop?
The lock-nut braking system uses a wing-nut that travels along a threaded axle. As the threaded axle turns a wing nut travels along the threaded axle until it lock tight against the frame of the vehicle, or the axle, causing the vehicle to come to an instant stop.
How do you propel a mousetrap car?
The most basic design for propelling a mousetrap racers is to tie one end of a string to a mouse trap’s snapper arm and then attach the other end of the string to a drive axle. By turning the drive axle the string is wound around the drive axle causing the mouse trap’s spring to compress and store energy.
