Table of Contents
What is a jointer and how does it work?
A jointer creates a flat surface on wood, and yes, it can be used to correct bow and warp on one side of a board at a time. “A planer is a thicknesser. In other words, you put a board into the planer to make it thinner after you have already established one flat side using the jointer (or a hand plane.).
What is the purpose of a jointer?
The jointer derives its name from its primary function of producing flat edges on boards prior to joining them edge-to-edge to produce wider boards. The use of this term probably arises from the name of a type of hand plane, the jointer plane, which is also used primarily for this purpose.
Do you really need a jointer?
Simply purchase your lumber already milled in S3S or S4S form (surfaced on three sides or surfaced on 4 sides). If you’re at a point in your woodworking where you’re starting to use rough sawn lumber, say from a lumber mill or your local sawyer, then a jointer is absolutely essential to your shop workflow.
Why use a jointer instead of a planer?
The jointer is used to flatten one face and square up one edge and the planer is then used to make the second face flat and parallel to the first. And speaking of thickness, a jointer will not allow you to easily thickness boards to a precise dimension. A planer on the other hand was born for the task of thicknessing.
Where is the danger zone when working on a jointer?
Danger Zone-The jointer danger zone is 3″ out from the cutterhead and knives and 8′ directly in front of the cutterhead. When you use the jointer, stand to the left of the machine (opposite the drive shaft) and keep your hands away from the knives. Always wear proper eye and ear protection.
Can I use a table saw instead of a jointer?
Using Your Table Saw as a Jointer. With the addition of a simple shop-made fence, you can easily edge joint on your table saw. Remember that man-made materials like plywood can be hard on steel jointer knives – but not on carbide table saw blades.
Can you use a jointer on both sides?
No, you cannot. This will make the board square, but it will NOT ensure it doesn’t taper. With the jointer you can only make each corner square. You can’t make the opposing faces parallel with each other.
Does DeWalt make a jointer?
Machine overview The DeWalt DW733S is a jointer planer combo (planer thicknesser) made by DeWalt until 1999.
Can you plane warped wood?
Mark the shim locations, remove the board and hot glue the shims into place. Then glue the board to the shims and the plywood with a dab of hot glue. Send that rascal through until it’s flat, then pull it free and plane down the other side.
What hand tool can take the place of a jointer?
give or take…so it’ll will work great for flattening and jointing along the length of the board. Many furniture parts are under this length, so a jack plane is quite flexible as a jointer plane. And the jack plane can work somewhat well as a smoothing plane.
How long should a jointer plane be?
Jointer planes are typically 20 to 24 inches (510 to 610 mm) long, and are the longest hand planes commonly used. Under the Stanley Bailey numbering system #7 and #8 planes are jointer planes.
What is a good size jointer?
An 8-inch wide jointer allows me to joint wider boards than a 6-inch jointer, and 8-inch jointers usually come with longer infeed and outfeed beds, adding more support to the lumber. And 8-inch jointers are usually affordable enough for hobbyist woodworking shops.
What should you never adjust on a jointer?
Don’t adjust out-feed table. Don’t try to remove more than 1/16” at a time. Don’t joint stock less than 1/4” thick. Don’t joint material shorter than 10”.
How much should a jointer take off?
I normally set the depth of cut on my jointer to approx. 1/32″, and often make two passes to remove enough stock to produce a perfectly square edge.
What causes kickback on a jointer?
A board or piece of one, resting on top of the cutter head will experience a force moving it to the operator’s right. If that force is unopposed by the operator adequately pressing the board down and to the left, the board may be thrown to the right. This motion is known as “kickback”.
What are the parts of a jointer?
A jointer has four main components; an infeed table, an outfeed table, a fence, and a cutter head. The infeed table and outfeed table sit coplanar, meaning they’re on the same plane and perfectly flat.
