Table of Contents
Where does the water drain in a clawfoot tub?
Source and drain lines come through the floor. In a typical clawfoot tub installation, both the water source pipes and the drain pipe enter the bathroom through the floor.
Why are clawfoot tubs bad?
“It doesn’t butt up against the wall, so you get a lot of spillage and it can cause damage to your wall or can seep in and actually drip down from your bathroom to your lower level ceiling,” Jonathan Scott of HGTV’s Property Brothers, told PopSugar. Consider tiling bathroom walls or nixing a clawfoot tub altogether.
How do freestanding baths drain?
The process of plumbing a freestanding bath works the same way as regular bath tub being plumbed, with a waste in the front leading to the drain pipe adjacent to the hot and cold water pipes that stop at your tub, or continue up to your shower.
What do the numbers on the bottom of a cast iron tub mean?
The cast iron is exposed on the outside and bottom of the tub, and although it may have been painted, the manufacturer’s stamp — if there is one — is often clearly visible. This number states the length of the tub in feet. Possibilities include 4, 4 1/2, 5, 5 1/2 and 6.
How many gallons does a cast iron tub hold?
Alcove cast iron bathtubs are usually 60 inches long, hold 32 gallons of water, and weigh 320 pounds on average. Freestanding cast iron bathtubs are 60 to 75 inches long, hold up to 82 gallons of water, and weigh an average of 385 pounds; however, large ones can weigh up to 500 pounds.
Does a clawfoot tub need AP Trap?
Not lavs. A claw foot tub has the p-trap below the floor. If you are using a slip joint waste and overflow, the theads are about at floor level which puts the slip joint nut accessible from above.
Why do people like clawfoot bathtubs?
PRO: Clawfoot tubs that include a hand shower are much easier to clean than a traditional tub because the flexible shower hose allows you to target water to wash and rinse any part of the tub easily. It also allows you to wash or rinse big things – like, say, a dog – more easily than you could in a traditional bathtub.
How far should clawfoot tub be from wall?
The distance between your tub and wall should be between 15-18 inches or at least 1 foot.
Does a clawfoot tub add value to a home?
According to the RealEstate.com survey, starter homes with claw-foot tubs sold for nearly 30% more than expected. Coffered ceilings also helped homes sell for 30% more than expected, and farmhouse sinks (thanks Joanna Gaines) helped homes sell for 26% more than expected.
Are all clawfoot tub cast iron?
Clawfoot tubs are traditionally made from cast iron, but they are also made from acrylic materials as well.
How much does it cost to Reglaze a clawfoot tub?
The average cost to refinish a clawfoot tub is $300 to $650, depending on the size and condition. Clawfoot tub issues such as erosion, rust, pinholes, scarring, lead paint, or chips need to be addressed before reglazing. Refinishing takes 4 to 5 hours and typically comes with a 3 to 10-year warranty.
Do freestanding tubs have an overflow drain?
Some bathtubs, such as freestanding or clawfoot tubs, look better without an overflow drain. You can install a floor drain instead, so that any overflow gets drained away properly, instead of damaging your floors and potentially ceilings.
Where is the drain in a freestanding tub?
All bathtubs drain in basically the same way, with a drain assembly located on the bottom of the tub linked to an overflow that may or may not have a toggle switch. When the plunger or stopper is opened, water drains out of the bathtub, through the drain assembly, down a tailpiece and into the trap.
How do I stop my freestanding tub from moving?
Carefully set the tub in position and adjust the tub feet as necessary until level. Once level, apply a generous bead of silicone on the bottom of the feet. This will prevent the tub from shifting after installation.
When did clawfoot tubs go out of style?
The Crane Company introduced colored bathroom fixtures to the United States market in 1928, and slowly this influx of design options and easier cleaning and care led to the near demise of clawfoot-style tubs. In the 1960s fiberglass bathtubs became the standard for homes, being lightweight and inexpensive.
What is a gate mark on cast iron What does it mean?
Cast iron is made with a sand mold in which liquid iron needs to be poured into it (or injected into the mold.) The liquid iron then hardens and the mold is removed from around it. In the 1800s the iron was poured in via a line on the bottom of the mold which left the line, or gate mark, on the iron once it hardened.
How heavy is a cast iron clawfoot tub?
All bathtubs are heavy, but clawfoot tubs tend to be especially heavy – particularly the cast-iron models. A cast-iron tub can easily weight 200-400 pounds while empty – fill it with water and climb in and you’re looking at several hundred pounds of weight.
Can you scrap a cast iron tub?
If you have a cast iron sink or tub, it may very well be worth scrapping, especially if you can’t find some way of selling it to someone else. While you can find ways to repurpose a cast iron sink or tub, you may also need to get rid of it from your home.
Are cast iron tubs still made?
Enameled cast iron tubs have been in use practically since the advent of modern plumbing. Today, these tubs are still popular due to their timeless appearance, excellent durability, and easy maintenance.
