Table of Contents
Follow these 5 simple steps to reset your sump pump: Disconnect the power. Take the sump pump out of the basin. Clean out the sump pump. Return the sump pump to the basin and restart the power. Reset the sump pump.
Where is the reset button on my sump pump?
How to Reset a Sump Pump Locate the reset button on the motor. If there isn’t one, locate the on/off switch and turn it off, or unplug the pump directly from the electrical outlet. Look inside of the sump pump. Plug the pump back in or move the switch back to the on position if there was no reset button.
What is the most common reason for sump pump failure?
The most common reason for sump pump failure is an electrical power outage as a result of bad weather or a storm. Sump pumps depend on your home for power and these blackouts can be problematic. Because power outages happen at random, the best way to combat this is by having a backup generator.
What to do if sump pump is not working?
Sump Pump Doesn’t Turn On Make sure the unit has power. Check to see that it’s plugged in and that the circuit has power via the home’s main electrical panel. Test the outlet to ensure it’s working. Check the float switch to see if the pump turns on when you manually lift the float. Check the impeller for clogs.
Do submersible pumps have a reset button?
(Labeled on the side of the pressure switch, the lever should be in the AUTO (down) position.) (You should hear water moving into the pressure tank from the well.) Hold the reset lever in the start position until the pressure builds up and the gauge reads over 40 PSI; then let it return to the AUTO position.
Will unplugging sump pump reset?
If your sump pump does not have a reset button, unplugging it from its power source like we did in Step 1 will suffice to cycle the system’s motor. If your sump pump does have a reset button, now is the time to use it. Many sump pump problems can simply be solved by resetting the pump.
Do sump pumps need to be reset?
If your sump pump is not running quite as good as the day it was installed it might need to be reset. Your sump pump is responsible for pumping ground water that builds up in your basement into the sewer or drain. Resetting your pump is easy and only takes a few minutes.
Will basement flood if sump pump fails?
If the sump pump fails during a big rain event, the basement can flood causing extensive water damage to your property, in addition to creating a huge mess. The most common cause of sump pump failure is a power outage.
How do you know when your sump pump is going out?
Signs It’s Time to Replace Your Sump Pump Makes strange noises. Sounds coming from your pump can indicate worn or damaged parts. Vibrates Excessively when Running. Infrequent Pump Usage. Runs All the Time. Irregular Cycling. It Runs for a Long Time. Visible Rust. Seven Years Old or Older.
Should there be water in my sump pump pit?
It’s perfectly normal for a sump pump pit to always have some water in it. This water can be the result of rain, snowmelt, or seepage from the ground. That being said, when the water rises to a certain level, this should trigger your sump pump’s float switch. This will cause the pump to turn on and start working.
Why is my sump pump not pumping?
A worn-out or malfunctioning float is sometimes the reason your sump pump has stopped working. Fill the sump pit with water and that should make the pump start on its own. If it doesn’t start, the float may need to be replaced.
How do you clear a clogged sump pump?
Remove the drain pipe by loosening the clamps that attach the pipe to the sump pump. Use a plumber snake or a metal hanger wire to push any blockage through the pipe. Use a hose (higher pressure, if possible) to flush the pipe and clean the inside walls.
Why is my sump pump not pumping water?
A small air relief hole should be in the discharge line so that the sump pump can overcome air pressure. If your sump pump was installed in an area where dirt or gravel is present, your discharge pipe might have debris in it which can disturb the sump pump’s float arm.
Why my well pump stop working?
Your well pump may have stopped working due to lack of power. Sometimes resetting a breaker or replacing a fuse affected by a power surge or brownout can fix this. If the well pump circuit breaker has tripped, the well pump itself may be failing. Then switch the circuit breaker off and on.
How do I restart my water pump after a power outage?
Using your insulated pliers, in case of stray electrical current, lift the lever upward. You should hear the pump kick on. Hold this lever in the upward position until you notice the pressure gauge get up to above 30 or so. Now if you turn it loose the pump should stay on and you are back in business.
What causes sump pump alarm to go off?
Sump pump alarms typically start to go off when there’s too much water in the area. If the sump pump alarm is functioning properly, but it’s going off too regularly, that means there is too much water pooling in your basement.
