Table of Contents
STEP 1: Calculate how much plywood you’ll need for your shiplap walls. STEP 2: Buy ¾-inch AC plywood. STEP 3: Gear up. STEP 4: Rip your plywood into shiplap boards. STEP 5: Sand each board. STEP 6: Paint your shiplap boards. STEP 7: Sand and apply a second coat of paint.
Do you start shiplap from top or bottom?
You can start applying shiplap either at the top or at the bottom of your wall. If you start at the bottom, gravity will work for you. If you start at the top, you’ll have to prevent each board from falling before you nail it in place.
Can you install shiplap over drywall?
You can install shiplap right over the drywall. However—and this part is crucial—you must first take the time to find all the studs within your walls and mark them carefully before you place a single board.
How do you nail shiplap?
For shiplap with a smooth prepainted surface, like our Timeless nickel gap shiplap, you’ll want to use adhesive and nails. Instead of nailing through the face of the board, you’ll only nail through the flange of each board to avoid any visible nail marks that will affect the overall look of your wall.
What adhesive do you use for shiplap?
Shiplap can be installed directly to sheet rock/drywall. Simply mark the stud locations for nailing the shiplap or you can apply a construction adhesive such as liquid nails.
Should you stagger shiplap?
Staggering Shiplap Creates A Balanced Aesthetic If you stack seams on top of each other, you’ll create an eyesore that draws your eye to the dark lines of the jointed ends. Building pros agree that staggering seams provides a better looking aesthetic. See the difference between these two installations.
What’s the best way to paint shiplap?
Overall, I will say that 99% of the time, painting shiplap with a paint sprayer is the easiest and fastest method! If you don’t have a paint sprayer, you can still paint shiplap with a paint brush and roller. Simply buckle in for a good chunk of time commitment.
Do you screw or nail shiplap?
Nails are the best options when installing shiplap cladding. Trim nails are faster to install than screws since you do not need to predrill the material and won’t be risking causing unsightly splits.
Do you have to remove drywall to install shiplap?
You don’t have to put your shiplap over drywall if there isn’t existing drywall already in place. However, if you are simply remodeling a room, you can certainly put shiplap over existing drywall.
Should you remove drywall before installing shiplap?
If don’t already have drywall installed, you do not need it as a base for affixing shiplap. You can install shiplap directly to your studs to save on time, money, and mess.
Do I need a vapor barrier behind shiplap?
You will need a vapor barrier as well as an expanding spray foam to seal any possible air and draft penetrations. I would use a 3/4″ T&G horizontally. That is what is shown in your photo. You will first need to either shim or shave your wall studs to make sure you Do not have any humps or dips in you walls.
Should shiplap be face nailed?
We always recommend face nailing shiplap and tongue and groove when installing it on your walls, ceiling, and as exterior siding. Face nailing means that you shoot your nail at a 90 degree angle to the board through the flat (or face) of the board.
Should I fill the nail holes on shiplap?
Don’t forget to fill in any nail holes and gaps in the shiplap with spackle or caulk prior to painting. If you painted the shiplap prior to installation, fill in holes and gaps after the shiplap is in place and then touch up these areas with paint.
What size nail gun do I need for shiplap?
You’ll want to use a 18 gauge nailer with 1 3/4″ to 2 1/4″ brad nails. If you’re using traditional shiplap planks, make sure to top edge which has the grove or cut out section is under the corresponding grove on the next plank. Shiplap traditionally has a 1/8″ space.
Can you glue up shiplap?
Shiplap planks can be fastened to walls either vertically or horizontally. Simply nail through the drywall directly into wall studs. You can use construction adhesive when installing on ceilings or over other surfaces, as long as they’re in good condition.
Can you glue shiplap to ceiling?
Use an adhesive such as Loctite (liquid nails) to keep the boards from twisting or popping. Then finish with brad or 2” finishing nails. Use liquid nails to ensure a secure bond.
How do I install shiplap directly to studs?
How To Install Shiplap Step 1: Find The Studs. First and foremost, you will need to find the vertical studs that are behind the drywall. Step 2: Check The Marks. Ensure your lines are vertical by using a level. Step 3: Install The First Shiplap Board. You’ll need to measure the shiplap board and the wall to cut it to fit.
Can you put up shiplap without a nail gun?
If not using a finish nailer, you need a hammer and nails. Cordless Circular Saw or Miter Saw and a safe place to cut it (work table or saw horses for a circular saw or work table or other stationary place for your miter saw). You may also need a jigsaw (see Step 3) but can easily complete this without it.
Can you use Command strips on shiplap?
When you’re ready to start installing your shiplap wall, take two command strips and place on either side of a plank. Measure how far apart the strips are and place the other side of the strips (the wall side) on the wall equally far apart.
