Table of Contents
Six Steps to Install Roll Roofing Step 1: Prepare the Roof. In preparation for installing the roofing material, you first want to clean the roof. Step 2: Apply Roofing Cement to the Edges. Step 3: Attach the Base Sheet. Step 4: Attach the Second Sheet. Step 5: Seal the Vents. Step 6: Overlap the Valleys.
Do you nail down roll roofing?
Do you nail down roll roofing? Nails are typically used to secure this type of roof. You can nail the separate layers by hammering the nails in 10-inch intervals across the roof. After that, you’ll want to use cement to cover them and seal them in place.
Does roll roofing require underlayment?
Q: Should I underlay my roll roofing? It depends on your budget, but installing an underlay is not out of necessity but preference. While roll roof underlay is not costly, they offer some layers of protection. Make sure you nail down the underlay and then roll it, making sure it is both smooth and flat.
How much should rolled roofing overlap?
The piece should overlap the lower course by at least 4 inches. Cut a hole in the roll roofing and slip it over as well. Embed both roofing pieces in cement.
Can I put rolled roofing over rolled roofing?
Rolled roofing is very adaptable and can be cut into 12-inch by 36-inch strips to act as hips and ridges or 9-inch strips for eaves and rakes. If removing your current shingles is a problem, it is usually permissible to re-roof over your existing roof with rolled roofing.
Can you shingle over rolled roofing?
Shingles can be applied directly over rolled roofing. There are two approaches to installing new shingles on a home. The second approach is to do what is called an “up and over.” In an up and over, the new roofing is installed right over the old roofing materials.
How do you cut rolled roofing?
Align the blade of the utility knife with the notch you placed on the edge of the rolled roofing, roll the piece of roofing toward the utility knife and then pull the utility knife across the width of the rolled roofing with the handle of the knife resting against the side of the roll for a straight cut.
What is the minimum pitch for rolled roofing?
As a primary roof covering, roll roofing is used on slopes down to one inch per foot. If the exposed nail method of application is used the minimum required slope is two inches per foot. The roofing is applied either parallel to the eaves or parallel to the rakes.
How long will rolled roofing last?
The average lifespan of asphalt roll roofing is 5 to 10 years. With proper maintenance, you can expect to get the maximum life from your asphalt roll roof.
Do you need a starter strip for roll roofing?
By installing an underlayment, you’ll extend the life of your rolled roofing material. Cut a strip of roll roofing approximately 18-inches wide (this is going to be your starter strip). Apply about a three inch layer of roofing cement along the eaves of your roof where you are going to begin your installation.
How do you use Henry roll roofing adhesive?
HE203 – ROLL ROOFING ADHESIVE is suitable for application with a notched squeegee or 4-knot roofing brush. Stir adhesive to uniform consistency before using. Do not thin. Apply adhesive evenly and uniformly with full coverage between each layer.
What is the best underlayment for rolled roofing?
Tyvek is a good choice as an underlayment to roofing products other than asphalt shingles—things like cedar shingles and metal roofing. It’s also a fully weatherproof underlayment, which is a huge advantage in areas that see a lot of extreme weather events.
Is shingles better than roll roofing?
Roll roofing has a typical life span of 5 to 8 years. Shingles have an expected life of at least 20 years, and the better grades can carry warranties of 30 to 50 years. Shingles are less likely to crack when exposed to sunlight and rain, and most shingles will fare better when subjected to hail than roll roofing will.
What is MSR roll roofing?
It is similar to asphalt shingles but is an oil-based asphalt product that has a mineral surface and comes in a large roll. It is known as an “MSR” which stands for mineral surface roofing. This roofing product comes in 100 square feet rolls and weighs about 75 pounds.
What do you cut roll roofing with?
Cut the rolled roofing to the right size using a razor knife. The rolled roofing should reach the chalk line when you lay it down and should stretch from 1 side of the roof to the other. You’ll need to use plenty of pressure with the razor knife to cut the rolled roofing material.
How do you slope a flat roof for drainage?
For drainage purposes, the current building codes require a minimum two percent slope or a one-fourth unit vertical for every 12 units horizontal. In other words, the roof must slope one-fourth of an inch for every 12 inches. The slope is barely noticeable to the naked eye.
How much is a roll of rolled roofing?
Cost of Roll Roof Roll Roof costs Zip Code Sq. ft. Basic Better Roll Roof – Material Prices $165.00 – $175.00 $190.00 – $210.00 Roll Roof – Installation Cost $220.00 – $240.00 $265.00 – $280.00 Roll Roof – Total $385.00 – $415.00 $455.00 – $490.00.
How much slope should a flat roof have?
What Pitch is a Flat Roof? If flat roofs are to work well, they have to have a slope, known as a fall, to shed rainwater. The fall should never be less than 1:80 and preferably about 1:40.
