Table of Contents
Whether your divots occurred during the pouring process of your countertops, or afterwards due to a soft cure, the solution is always to pour another coat of epoxy. You can pour directly over the previous epoxy pour within 24 hours of the first pour.
Why am I getting dimples in my epoxy?
Dimples can occur for 3 reasons: temperature fluctuation, micro dust particles and overtorching. To avoid getting dimples in your cured resin, make sure that the temperature in your resin room stays stable, that you use a dustcover and that you only lightly torch your resin!Feb 13, 2019.
How do you fix epoxy craters?
Lightly sand the existing epoxy with 120-150 grit. Care should be taken not to cut through the stain. Apply another seal coat of epoxy using an 1/8″ nap foam roller, working to fill in the craters. Allow the epoxy to cure hard, sand entire application flat, and re-coat to finish.
Do I need to sand between coats of epoxy?
Sanding will not only get out the imperfection but will also serve to provide some tooth between the first and second layers. It will look very scuffed in the short term but do not worry, once you pour the second coat over top, all of those sanding marks will disappear.
Why isn’t my epoxy smooth?
The most common cause for uneven epoxy resin is often not using the correct mixing ratio, or even using hardener and resin that is too old. These problems can be prevented by ensuring your work area is well ventilated, not too humid, and using a torch to heat the epoxy and allow the air bubbles to escape.
Why do I keep getting fish eyes in my epoxy?
Substrate contamination is the most common problem that causes fish eyes and pin holes in epoxy seal coats. Dust, dirt, wax, silicones, even the oil from your fingers when touching the part prior to sealing with epoxy will deter epoxy resins from laying flat and curing with a perfectly smooth surface.
Why is my epoxy not sticking to my cup?
Mixing ratios can greatly affect how your piece will cure. If the mixing ratio is off or not completely mixed properly, this can cause the resin to remain tacky, or have soft spots. To ensure that you have the proper mixing ratios measured in measuring cups, and to ensure that you are mixing by volume.
Can you pour epoxy over cured epoxy?
Can I put another coat of epoxy over cured epoxy? Yes. Since the epoxy has cured a chemical bond is not possible so what is called a mechanical bond is needed. This simply means that the cured epoxy has to be lightly sanded before the next coat is applied: the first coat should have a matt, almost white, surface.
How do you smooth epoxy edges?
After letting the resin run down the sides of your artwork, and letting it cure for 24 hours at the bare minimum, use sandpaper (80-200 grit) or a power sander to smooth out the edges of your artwork. Once each side is smooth, you may paint them the color of your choosing.
Why is my resin bumpy?
This problem can be caused by anything floating/falling into your resin while it cures, resulting in imperfections in the surface. If you are experiencing imperfections that look more like domed bumps in the resin, skip down to #4.
Why is my resin wavy?
Sometimes, resin components can crystallize when the kit has gotten too cold. These crystals can show up as swirls or waves in resin. Before using the kit again, gently warm it in a warm water bath. Moisture has contaminated the resin.
How long does epoxy need to dry before sanding?
Tip: The epoxy resin must be really dry before sanding. You should therefore allow a waiting period of at least 48 hours before processing. Follow the manufacturer’s instructions, as there are resins that take even longer to harden completely.
Is one coat of epoxy enough?
Manufacturers may suggest two coats of epoxy paint and topcoat, but most standard kits only supply enough for one coat. If you choose to add color flakes, which will help hide concrete’s inherent imperfections, determine how heavily you’ll broadcast them across the floor so you don’t come up short.
How soon can you pour a second coat of epoxy?
When using epoxy, it can be a helpful process to add a second layer, but you want to make sure to follow the correct procedures. With most coating epoxies, if you are trying to build up to your desired thickness, it is recommended to pour your second coat once the first coat is tacky to the touch (usually 4-6 hours).
How do you fix fisheye?
SOLUTION Remove wet paint film with solvent, clean and refinish. Add the recommended fisheye eliminator and respray the affected area. If fisheyes appear in a basecoat, allow the color to flash then spray a mist coat over affected area.
Why did my epoxy get hot?
The main reason that epoxy gets so hot is due to the exotherm during the curing process. When base epoxy resin and the hardener (curing agent) are mixed, there is a chemical reaction that causes them to heat up. This helps with the curing process itself.
Why is my epoxy so thick?
Temperature The ideal room temperature for mixing ArtResin epoxy resin is between 75 and 85 degrees F or 24 – 30 degrees C. If it’s colder than that, the resin will be thicker and harder to mix, will have more bubbles and will take longer to cure until it’s dry to the touch.
Why is my resin still sticky?
Sticky resin is typically caused by inaccurate measuring or under mixing. Sticky, tacky resin: often caused by inaccurate measuring, not mixing thoroughly or by curing in cold temperatures. Try moving your piece to a warmer spot: if it doesn’t dry, re-pour with a fresh coat of resin.
Can you put polyurethane over epoxy?
Both oil-based and water-based polyurethane can be applied over epoxy, although oil-based polyurethane may leave an amber hue (while water-based will be more clear). To ensure proper application, be sure that the epoxy has completely sealed/hardened, and sand first to allow for a mechanical bond.
How do you get bubbles out of epoxy after it dries?
Yes, you CAN get rid of bubbles after your resin has dried! Simply sand down the entire surface of your piece, making sure you pay special attention to the areas with bubbles. Wipe away all the sanding residue with a damp paper towel. Apply a fresh coat of carefully measured and mixed ArtResin epoxy resin.
