Table of Contents
What is the formula for slip?
It is common to express the slip as the ratio between the shaft rotation speed and the synchronous magnetic field speed. When the rotor is not turning the slip is 100 %.Number of poles, frequencies and synchronous induction motor speed. No. of Magnetic Poles Frequency (Hz) 50 60 6 1000 1200 8 750 900 10 600 720.
What is slip in 3 phase induction motor?
Slip in Induction Motor is the relative speed between the rotating magnetic flux and rotor expressed in terms of per unit synchronous speed. When a three phase power supply is connected to the three phase stator winding of induction motor, a rotating magnetic field is produced in the air gap.
How do you calculate slip frequency?
The frequency of a voltage or current induced due to the relative speed between a vending and a magnetic field is given by the general formula; Frequency = PN /120 Where N = Relative speed between magnetic field and the winding P = Number of poles For a rotor speed N, the relative speed between the rotating flux and.
What is the equation for rotor frequency of 3 phase induction motor?
Explanation: Rotor frequency = s*f1 = 90/60 = 1.5 Hz. rotor speed = 1000(1-0.03) = 970 rpm. 11. A 4-pole, 3-phase slip ring induction motor is used as a frequency changer.
What is the slip frequency?
Slip frequency can be measured by determining the phase angle traversed in a defined period. For example, with a slip setting of 2 seconds (0.055 Hz) and slip frequency of 0.04 Hz, an angle of approx 29° (elec) is traversed before synchronising is permitted, as shown in Fig 12.15.
What is full load slip?
The slip corresponding to full load speed of th motor is called full load slip. Example 1 : A 4 pole, 3 phase induction motor is supplied from Hz supply. Determine its synchronous speed. On full load, its speed is observed to be 1410 r.p.m. calculate its full load slip.
How is slip in motor calculated?
What is Slip in an Induction Motor? Definition: In Induction Motor, a slip is a speed among the rotary magnetic flux as well as rotor expressed in terms of for every unit synchronous speed. It can be measured in dimensionless & the value of this motor cannot be zero. S = (Ns – Nr) / Ns. Slip = (Ns-Nr/Ns)*100.
What is slip speed?
The speed at which the induction motor work is known as the slip speed. The difference between the synchronous speed and the actual speed of the rotor is known as the slip speed. In other words, the slip speed shows the relative speed of the rotor concerning the speed of the field.
Can slip be negative?
If the rotor of an induction machine rotates above synchronous speed, slip is negative, as are torque, mechanical output power and air gap power. i.e. the machine is operating as a generator. Rotational losses are 2450W.
What would be the rotor slip frequency?
The operating speed No = N – Ns where Ns is the slip speed. The frequency of the rotor current fr = Ns x P/120, so fr = 0 if the slip is zero. If the operating speed is zero, Ns = N and the frequency of the rotor current is the same as the frequency of the stator current. f = source frequency in Hz.
What is slip torque?
The torque slip curve for an induction motor gives us the information about the variation of torque with the slip. The slip is defined as the ratio of difference of synchronous speed and actual rotor speed to the synchronous speed of the machine.
What is the slip equation for stroboscope method?
The devices used in the stroboscopic method are known as stroboscopes. The synchronous speed of the rotor in RPM N = 120f/P where f is the frequency of the stator current and P is the number of poles. The operating speed No = N – Ns where Ns is the slip speed.
What is standstill rotor EMF?
When rotor is stationary i.e. s = 1, the frequency of rotor e.m.f. is the same as that of the stator supply frequency. The value of e.m.f. induced in the rotor at standstill is maximum because the relative speed between the rotor and the revolving stator flux is maximum.
Can a 50 Hz motor run on 60 Hz?
Electrical machines designed for 50Hz can usually work safely in 60Hz power supply, but not applicable to 60Hz machines to be run in 50Hz power supply.
Which induction motor has maximum speed?
Synchronous and full load speed of amplitude current (AC) induction motors Speed (rpm) Number of Poles Frequency (Hz, cycles/sec) Synchronous Full Load 2 3600 2900 4 1800 1450.
What is slip current?
“Slip” in an AC induction motor is defined as: As the speed of the rotor drops below the stator speed, or synchronous speed, the rotation rate of the magnetic field in the rotor increases, inducing more current in the rotor’s windings and creating more torque. Slip is required to produce torque.
What is synchronous speed and slip?
Slip is the difference between the synchronous speed of a motor and its actual speed. Mathematically it is determined by. Slip = Synchronous Speed − Actual Speed. Using the example above for synchronous speed of a motor with four poles operating at 60 hertz, the value was calculated to be 1800 RPM.
What is the importance of slip?
Slip creates a relative speed between the RMF and rotor. That keeps a torque continuously acting on it when the motor is running. So what would happen if slip becomes zero? Bcoz there will be no relative speed between RMF and rotor, and which will stop inducing rotor current.
What is no load slip?
The speed is assumed to be synchronized. The synchronous speed can be achieved by taking slip = 0 which creates infinite impedance in the rotor branch. Rotor copper loss at no load is very less that its value is negligible. Small current is required to produce adequate torque.
What is value of slip at no load?
At no-load condition, the rotor speed is almost equal to the synchronous speed. e.g A 4 pole, 60 Hz induction motor at no load turning at ηr = 1790 RPM will have slip = (1800 – 1790)/(1800) = 0.55%Mar 9, 2020.
What is the formula for efficiency at full load?
Then the efficiency of transformer can be written as : Where, x2Pcufl = copper loss(Pcu) at any loading x% of full load.
