Table of Contents
Measure the length and width of the area in feet and multiply the figures together. Multiply your area figure by the depth of gravel that you wish to use, ensuring your measurement is also in feet. If your depth is in inches, divide it by 12 first. You now have a cubic feet volume figure.
How much gravel do I need to cover an area?
If you want to cover an area with gravel, 1 to 2 inches should be sufficient depending on the size of the gravel. If you are using 3/4″ inch gravel or larger figure on at least 2 inches in depth to get good coverage.
How do you measure for landscaping gravel?
How much gravel do I need? Determine the length and width of a cuboidal excavation. Calculate the area of the excavation, multiplying the length and width together. Determine the depth of the excavation. Multiply the area and depth of the excavation to obtain its volume in cubic yards: 18 * 2 = 36 yd³ .
How do you figure square feet of gravel?
Multiply the length by the width to determine the square footage. Multiply the length by the width to determine the square footage. Use a calculator to perform the multiplication if necessary. For example, multiply a length of 12 by a width of 10 to equal 120 square feet.
How many square meters does a ton of gravel cover?
How many square meters does a ton of gravel cover? One tonne will cover 14 square metres. If you want to apply them in a normal depth 50 mm for a driveway. 1 tonne will be sufficient to cover approximately 20 square metres for pedestrian pathways, 35mm depth is normally sufficient for pedestrian pathway.
How many square feet will 5 tons of gravel cover?
Regarding this, “how much area does 5 tons of gravel cover?, typically, as 1 ton of gravel cover around 108 sq ft area for 2 inch depth, so 5 tons of gravel = 108 × 5 = 540 sf coverage, therefore 5 tons of gravel can cover around 540 square feet or 60 square yards or 50 square meters area for standard 2 inch depth.
How do I calculate how much gravel I need for my driveway?
Measure the length and width of your driveway in feet. Multiply the length by the width to get surface area and divide the result by three because 4 inches is 1/3 of a foot. You now have the volume of gravel needed in cubic feet. Divide the volume in cubic feet by 27 because there are 27 cubic feet in a cubic yard.
How many yards of stone do I need calculator?
Please enter the measurements below and press “Calculate” to receive the approximate number of cubic yards needed for the specified area.Building Stone Calculator. AGGREGATES FOR GROUND COVER (PER CUBIC YARD) DEPTH COVERAGE (STONE SOLD BY THE TON) 1” 300 SQ/FT PER YARD 2” 150 SQ/FT PER YARD 3” 100 SQ/FT PER YARD.
How deep should you lay gravel?
Decorative aggregates should be laid at a depth of 50mm. This ensures proper coverage without revealing the surface below. Laying the gravel too deep will mean you sink into the surface and it becomes difficult to walk across.
How many yards is a ton of #57 gravel?
Calculate #57 Limestone Gravel Coverage (Square feet) 400 sq ft Volume (Cubic feet) 67 cu ft Volume (Cubic yards) 2.5 cu yd Estimated amount (Pounds) 5,951 lb Estimated amount (Tons) 2.98 ton.
How much area does a 50 lb bag of gravel cover?
A 50-pound bag of pea gravel is equivalent to 0.5 cubic foot, so two 50-pound bags cover 1 cubic foot.
How many square feet does a 50 lb bag of gravel cover?
Consider a ½ cubic foot bag of stone or soil weighs about 50 lbs and will cover 2 square feet at 3″ deep.
How much rock do I need per square foot?
How much landscaping rock do I need? Material Suggested Depth Coverage Area per 1 ton 3”-8” rock 3”-8” 60 square feet 1”-3” rock 1”-3” 80 square feet 3/4”-1” screened gravel 2” 100 square feet 5/8”-1/2” screened gravel 2” 120 square feet.
How much area does a ton of 20mm gravel cover?
Based on our 20mm sized stones, 1 bulk bag of gravel will cover approximately 12 sqm at 50mm depth for paths and driveways.
What area will a 25kg bag of gravel cover?
For Decorative Gravel As a rule of thumb 1 of our 25kg bags will cover an area of 0.25m to a recommended depth of 50mm.
How far will a ton of gravel go?
A ton of gravel will cover approximately 100 square feet, 2 inches deep.
How much gravel is in a dump truck?
How many yards of gravel in a dump truck:- a standard sized dump truck is always recommended for your project. It can carry about 15 to 16.5 cubic yards of 3/4″ or pea gravel per truckload. Thus, a dump truck can have capacity to hold 15 to 16.5 cubic yard of gravel per truckload.
How many yards are in a ton?
Regarding this, “how many yards in a ton?”, generally for estimating purpose 1 yard of gravel weighs around 3000 pounds and 1 US ton = 2000 pounds, so yards in a ton = 2000/3000 = 0.66 cubic yards, therefore, there are 0.66 yards in a ton.
How many square feet will 16 tons of gravel cover?
How many square feet will 16 tons of gravel cover:- typically, as 1 ton of gravel cover around 108 sq ft area for 2 inch depth, so 16 tons of gravel = 108 × 16 = 1728 sq ft coverage, therefore 16 tons of gravel can cover around 1728 square feet or 192 square yards or 160 square meters area for standard 2 inch depth.
How many inches deep should a gravel driveway be?
A standard driveway is between 12 and 18 inches deep. Each of these gravel layers is a minimum of four inches deep, and some folks recommend making each layer as much as six inches. If you have a large area to dig out for your new driveway, the idea of a shovel and wheelbarrow may not be very appealing at this point.
How do I calculate driveway rocks?
To measure the driveway in cubic feet, multiply the length by width by depth. For cubic yards, divide the total cubic feet by 27. Because one cubic yard of gravel is equal to 1.13 tons, you can multiply your total cubic yards by 1.13 to convert this measurement to tons.
How much will a yard of gravel cover?
A yard of any material will cover approximately 100 square feet at 3 inches of depth.
