Table of Contents
How do you calculate steps for a deck?
To determine the rise and run of the steps, measure the distance from the floor of the deck to the ground and divide that number by 7.5. The result will be the number of steps the staircase will need (e.g., deck is 112″ from the ground; 112/7.5 = 14.93. Round up to get 15 steps).
How high should a deck step be?
Requirements for Deck Stairs Stair rails on decks should be between 34 inches and 38 inches high, measured vertically from the nose of the tread to the top of the rail. Treads must be at least 10 inches deep, measuring from front to back.
How do I figure out how many steps I need?
Divide the rise by 6 or 7 inches (15 or 18 cm) to find the total number of stairs. For larger stairs, divide by 6 and for smaller stairs, divide by 7. The total you get is how many stairs your future staircase will have so you can plan accordingly.
What size lumber is used for stair stringers?
The stair stringers are essentially the backbone of your staircase. Always use straight, high-quality, pressure-treated 2x12s for stair stringers. If you are planning on resting the stringer on the ground, make sure the wood has .
Do deck stairs need a landing?
SAFE, SUPPORTED STAIRS: Deck-stair construction varies, but the general requirements are consistent: proper footing support, and an adequate landing. Regardless of the stair run and number of treads, the stairway needs a footing at the bottom to support the stringers—they can’t just rest on the ground.
Do deck stairs need toe kicks?
The tread (or depth) of your steps should be ten and a half inches. The risers (or toe kick) must be between seven and eight inches high. A handrail is only required if your deck is more than thirty inches off the ground.
What size boards do you use for deck stairs?
Deck stairs are typically made from 2 x 12 stringers spaced about 12 to 16 inches apart. They rest on a solid foundation and are attached to the deck with hangers. They have risers (also called toe kicks), treads and railings.
Do you need a railing for 3 steps?
A: Editorial Adviser Mike Guertin replies: Since your stairs will have only three risers, you don’t need to install a handrail. That said, it’s important to count the number of risers accurately.
How wide should a step be?
The stair treads should be at least 36 inches wide. Despite these minimum requirements, we recommend that stairs should be at least 48 inches wide so they don’t feel cramped. The maximum allowable stair rise is 7 3/4 inches, and the minimum stair rise is 4 inches.
How tall is a 4 step Stringer?
Mendocino Forest Products Stair Stringer 4 step Redwood (Common: 48 in. x 12 in.; Actual: 1.5 in.
What is the standard step height for stairs?
Riser Heights In the United States, the step height standard should be between 7 or 7 ¾ inches at the most, and no less than 4 inches. You should follow other measurements if given by local building codes. In Canada, the maximum step riser height is 8 ¼ inches.
What is the best rise and run for stairs?
In my mind, though, the ideal stair rise-run is 7 1/4 by 10 inches. If you have to deviate from this, use the following rules of thumb: Unit rise times unit run (in inches) should equal 72 to 75. Two rises plus one run should equal 24 to 25 inches.
What should I put on the bottom of my deck stairs?
Your stair stringers will rest on your landing pad, but you should include a base plate. A bearing block is typically a 2×4 that connects your stringers.Footings with Different Deck Stair Landing Options Concrete landing pad. A wood box-type landing pad. Crushed stone. Patio Blocks.
Are stair stringers 2×10 or 2×12?
It is acceptable and within building code guidelines to use either 2×10 or 2×12 dimensional lumber to create a set of stairs; however, a stair stringer should not be less than 3.5 inches wide at its narrowest point to provide adequate strength for the load the stairs will be supporting.
How do you anchor stairs to a deck?
Attaching Stair Stringers to Rim Joist. The simplest way to attach stair stringers to a deck is to attach them directly to the rim joist of the deck using hangers or lag bolts.
Can you make stringers out of 2×10?
Pressure-treated or cedar 2×10 or 2×12 can be used depending on the depth of the cut-outs you’ll be using. By code you will need a minimum of 3-1/2″ of material left on the stringer after the cut-outs and that area should also be free of large knots which would weaken the stringer.
How thick should a stair stringer be?
According to general specifications, your stair riser thickness should be no less than ½”. In fact, many professionals recommend risers with a thickness of ¾”. It’s also important to note that if you do build a closed riser staircase, your stair treads will need to have a note as well.
How far apart can stair stringers be?
Cut stringers can be spaced no more than 18 inches on center, so a 3-foot-wide staircase needs three stringers, and a set of slightly wider stairs (say 3 feet 6 inches) needs four stringers. The maximum 18-inch spacing presumes treads of 5/4-inch wood decking or 2-by stock.
What is the best wood for outdoor steps?
Two types of wood widely considered the best for outdoor building of any kind are redwood and cedar. This is because they are both naturally resistant to weather damage, are easy to work with, and have a reputation for being long lasting wood even when not treated, stained, or painted.
