Table of Contents
This is a pretty straightforward process. Attach the backwash hose to the waste or backwash port. Turn the filter system off. Turn the multiport valve to Backwash. Turn the filter system back on. Let the water run out of the backwash port and through the backwash hose for about a minute, or until the water runs clear.
Do all pool filters have backwash?
Whether you choose to clean your pool with a sand or DE filter, you can easily backwash it on your own. All pool filters follow the same general steps for backwashing, but there may be small variations depending on the model you own. The owner’s manual should have detailed instructions for backwashing your filter.
What is the purpose of backwashing a pool filter?
The process of backwashing dislodges trapped debris and contaminants, flushing them out through your value’s waste line or a hose that is connected to the pool pump. When the filter media is clean, the pressure gauge is lower and water can easily flow in and out of the system.
How do I know when to backwash my pool filter?
As a general rule, you should be backwashing your pool about once a week or in conjugation with your scheduled maintenance. Another industry standard is to backwash when your filter’s pressure gauge reads 8-10 PSI (pounds per square inch) over the starting level or “clean” pressure.
How long does it take to backwash a pool filter?
Open the air bleeder assembly on your filter and turn pump on. Watch the pressure gauge for spikes. After the hose fills with water, backwash your sand filter for 2 – 3 minutes, or until water runs clear.
Do you lose sand when backwashing?
Excessive sand coming out when backwashing is not normal. Often, excess sand gets into the wrong places when refilling and will sand to come out into the pool or out of the backwash hose. But it should go away after a few runs. In general, you shouldn’t be losing sand from your sand filter.
How long do you rinse after backwash?
Turn the lever to RINSE, start the pump and rinse for about 15-30 seconds. Stop the pump and turn the lever to FILTER. This is the normal operating position. Close the drain outlet valve and start the pump.
How long should you backwash a sand filter?
After the hose fills with water, backwash your sand filter for 2 – 3 minutes or until water runs clear.
Does backwashing remove water from pool?
The backwashing process reverses the flow of water to flush out contaminants from a swimming pool filter. It should be carried out until water runs clear through the waste line.
Where does the backwash water go?
Any backwash water is to bypass the septic tank and be discharged to the drain between the septic tank and the common effluent drain.
Do you need to backwash a cartridge filter?
Unlike other filtration systems, cartridge filters don’t require backwashing, which means homeowners don’t waste the water and extra energy involved in backwashing. The small size of cartridge filters allows them to be run on smaller pumps because they can run with a lower flow rate pump, which saves energy.
How do you backwash an Intex above ground pool filter?
How to Backwash an Intex Pool Turn the pump filter off. Set the filter to back-wash. Connect a hose or pipe to the discharge port. Turn on the filter. Turn off the filter and set the filter mode back to its regular position. Disconnect the hose from the discharge port and store the hose.
How often should backwash a pool filter?
“When do we need to backwash?” – It is recommended to backwash your filter once every 4-6 weeks of regular use. Additionally, there are several instances that would require backwashing in between the normal monthly backwashing.
What is the difference between backwash and waste on a pool filter?
Drain/Waste: Opting the drain or waste setting will remove pool water without forcing it through the filter. Backwash: This clears out any debris, dirt and other contaminants that may have accumulated on the filter. Closed: if you choose this setting, then the flow of water to the pool and filter will be stopped.
Can you backwash with filter balls?
Yes, you save water with FilterBalls with the backwashing. Simply follow the FilterBalls installation instructions by noting your filter pressure upon installation and backwash when the pressure increases by 5-6 psi. Note your starting pressure will be much lower than what you experienced with sand.
Can you backwash a pool too much?
Can You Backwash Too Much? If you backwash your pool too much i.e. time duration and/or close frequency then yes you can cause a lot of problems. Some problems that can arise from backwashing your sand pool filter too much are: Loss of water – 500+ litres of water can be lost in each backwashing cycle.
How do you backwash a Hayward cartridge filter?
How do I backwash my filter? When the filter pressure rise 8-10 PSI over the clean starting pressure it is time to backwash. Turn the pump off and rotate the multiport valve to backwash. Turn on the pump and the dirty water will flow out the waste line.
When vacuuming a pool What setting should the filter be on?
For routine vacuuming, the filter valve is left in the normal “Filter” position. This directs dirty vacuum water through the pool filter to remove the contaminants, then conveys filtered water through return lines back to the pool. The “Filter” setting is used for light to moderate levels of pool sediment.