Table of Contents
If you remove the top washer panel, you can reach down into the washer and pull the tear shaped tab at the bottom of the door lock and it will unlock the door. On some of the Maytag washing machine models, there is a green plastic rope/string located near the detergent area that if pulled, will unlock the door.
How do I turn off the control lock on my Maytag washer?
To turn off Control Lock, press and hold the Options key that says “Control Lock Hold 3 Sec” under it for 3 seconds.
How do you force a washing machine to unlock?
Turn the washing machine off and unplug it. If pausing the cycle doesn’t unlock the door, turn the machine off. Then, unplug the machine and wait 5-10 minutes. Try pulling the handle again to see if the door opens. This is the most common solution for top loaders.
Why is my Maytag washer not unlocking?
Door Locked at the end of the Cycle If the washer will not unlock at the end of a wash cycle, unplug the washer or disconnect power. Wait approximately 2 minutes for control to reset. Reconnect power to washer (plug in). The door should unlock after this is complete.
How do you unlock a Maytag control lock?
Press and hold the designated control lock button for your model for 3 seconds. The location of the control lock button may vary depending on your model. Refer to the Owner’s Manual for the control lock button location for your model. The light will turn off and the control will be unlocked.
How do you unlock a washing machine mid cycle?
Press the “Start/Pause” button on the front of your washing machine and wait a few minutes for the washer to safely drain away water in the drum before it unlocks the door. Once this is done, you’ll be able to open the door and add/remove items or make chances to the cycle.
How do you manually unlock a front load washer?
How to Manually Open the Door Turn off and unplug the washer/dryer. Close the water faucet. Wait until the drum has stopped rotating – never open the door while the drum is in motion. Wait until water and laundry have cooled down when washing with high temperatures.
How do I reset my Maytag washer?
The easiest way to reset a Maytag washer is to disconnect the power to the washing machine for three minutes. Disconnecting the power allows the electrical charge to dissipate from the washing machine, which allows it to reset. If the reset fails, unplug the washer again, this time leaving it unplugged for ten minutes.
Why does my washer say control locked?
The Control Lock feature on Front Load Washers can prevent any selections from being made when activated. The controls can be locked or unlocked after a cycle has started.
How do you unlock the controls on a Maytag oven?
Door is locked when starting or using the oven Turn the power off at the circuit breaker or fuse box for one minute, then turn the power back on. Allow the oven to cool, approximately 30-90 minutes, move the latch arm to the left to unlock the door.
How long does it take for a washing machine to unlock?
If you’re going to attempt to open a door with a broken handle it’s advised that you turn the power off first and avoid using too much force. Please remember, most washing machines require up to 2 mins for the door to release open once the cycle has finished.
How do I reset my washing machine?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
How do you unlock the Control Lock on a Whirlpool washer?
If you do not see the 3-2-1 countdown and are unable to de-activate Control Lock, try pressing the POWER button first, then touch and hold 3 seconds to de-activate control lock. If this does not work, try unplugging the machine or turning off the breaker for 1 minute, then power the machine back on and try again.
How do I turn off the Control Lock on my Whirlpool washer?
Press the button for that dedicated key to activate and deactivate the Control Lock. To turn off Control Lock, press and hold the Options key that says “Control Lock Hold 3 Sec” under it for 3 seconds.
What are the codes for a Maytag washer?
Error Codes in my Maytag Front Load Washer Error Code Error Sud or Sd There are too many suds in the washing machine. F5 E2 The door is not locking properly. F7 E1 Indicates a motor speed sensing error, F8 E1 or LO FL The washer is sensing a low flow of water.
What does LoC mean on Maytag washer?
If you try to push buttons, you may see the code “LoC” or “LC” (depending on your model). This is a reminder that you have set the control lock and need to de-activate it to allow the washer controls to function.
How do you manually unlock a Whirlpool washer?
Hold down the “Control Lock” button on your Whirlpool washer for three seconds at the end of the washing cycle. Listen, and when you hear the unlatching sound, the door should open.
How do I reset the control panel on my Whirlpool washer?
Follow these steps to reset a Whirlpool washing machine: Make sure the power to the washer is turned on at the wall, but keep the Power button on the control off. Hold the Program button down while simultaneously pressing the Water Level button two times. When done correctly, the control panel lights should illuminate.
