Table of Contents
Do you need special solder for copper pipe?
Basic Soldering Torches When the joint is hot enough, molten solder instantly flows into the joint and covers the entire mating surfaces completely, almost as if following detailed instructions. As you’ll see, you don’t need special skills for soldering copper pipe fittings successfully.
What’s the best solder to use on copper?
What Type of Solder is Used for Copper Pipe? Lead free solder is best for copper pipes carrying drinking water. It will be free of elements you don’t want entering your drinking water. However it will require a higher melting point than a 50/50 solder.
Why is the solder not sticking to copper pipe?
If the solder is beading up or running down the pipe, you have a dirty fitting. Just as Vic says use clean fine grit sandpaper or emery cloth. Clean both surfaces, spread flux as soon as you clean them. Also clean and flux joint after you fit them together.
Can I solder copper pipe without flux?
Flux is a chemical which helps you solder. Flux prevents the copper from oxidizing as you heat the copper with the torch. You can solder without flux, but it is really difficult! Flux is applied to both the pipe and the fitting with a handy miniature paint brush.
What kind of torch do you use to solder copper pipe?
The torch needed for soldering copper can be propane or MAPP gas (methylacetylene-propadiene propane). MAPP gas comes in a yellow tank and propane comes in a blue tank. MAPP gas, usually a bit more expensive, gets much hotter than propane, so heats the pipe faster.
What kind of solder should be used on water pipes?
Lead-free plumbing solders are required for use on pipes carrying drinking water, also known as potable water lines. Leaded solders are available for applications that will not come into contact with potable water, such as sheet metal repair or copper drain lines.
Can you solder without flux?
Yes, solder can be used without flux. To do so, you will need something other than flux to break down the oxides on the metal surface, without which your surface may be damaged or not properly cleaned.
Can you overheat copper pipe when soldering?
Overheating is a major problem when brazing or soldering copper pipe because the flux will burn (become oxidized), stop working, and become a barrier to tinning. In addition, a heavy oxide can be formed on the pipe itself, preventing a bond from forming between the filler metal and the pipe surface.
Can you solder pipes with water in them?
Don’t try to solder pipes with water in them. Soldering a joint in pipes that contain even tiny amounts of water is nearly impossible. Most of the heat from the torch goes into turning the water to steam, so the copper won’t get hot enough to melt the solder. Stop the trickle of water with a pipe plug.
Can I solder copper pipe with a soldering iron?
You can fix it using a soldering iron, as long as you follow the basic rules of soldering copper wire and make sure you’re careful and attentive during the process.
What is the purpose of flux when soldering copper?
The main purpose of the flux is to prepare the metal surfaces for soldering by cleaning and removing any oxides and impurities. Oxides are formed when metal is exposed to air and may prevent the formation of good solder joints.
Can you use electrical solder for copper pipe?
Electrical solder is often a softer alloy, so it won’t withstand pressure as well. Definitely flux the pipe fittings as you normally would. You won’t get good coverage with the flux in the solder.
Can you use too much flux when soldering?
Although there is a sufficient amount of flux present in the core of the solder wire to get your job done, the technicians (to make their job easy) tend to use additional flux in form of paste or liquid during the rework on the PCB. There is no problem with the use of flux during soldering.
Why does my solder not stick?
A classic reason solder won’t stick to something is because you’re not getting it hot enough. My interns come to me with this problem all the time. Make sure the tip of the iron is nice and shiny. Touch some solder on it, and it should melt almost instantly.
Can I solder with a propane torch?
Swab a little flux around the end of the tubing and inside the ends of the elbows and then push the joint together. I used a common everyday, readily available propane torch to solder the copper tubing together. You can get a cylinder of propane and the torch at any big box home improvement or hardware store.
How long should you wait after soldering copper pipe?
Be sure to wait until the solder has cooled (2-3 minutes) before pressurizing the line to avoid the solder cracking due to a quick change in temperature.
Is electrical solder and plumbing solder the same?
Perhaps the key difference between electrical and plumbing solder is the type of flux used in each application. The flux also aids wetting, helping the solder to flow and bond with the metals more readily. Typically, electrical solder contains rosin core flux; plumbing solder uses an acid-based flux.
Can you use lemon juice as flux?
Cut six lemons in half with a kitchen knife. Squeeze the juice from a lemon into the strainer. Stir the juice in the container for 10 seconds with the wooden spoon. The citric acid flux you have made can now be used to prepare metal for soldering.
Can you Resolder a copper fitting?
Soldering vertical copper pipe shouldn’t be too different from working horizontally. If the joint and tip are hot enough, the solder should flow right in. Heat the middle of the fitting and apply the solder as soon as it starts to melt. Remove the heat once the solder starts moving.
