Table of Contents
How do I put my GE dishwasher in diagnostic mode? While the dishwasher is in stand-by mode, press and hold down the pads – Cycle + Start – at the same time for about five seconds. The door status will be checked first (for 10 seconds) with other error checks following.
How do I reset the control panel on my GE dishwasher?
Hold the Start button now for five seconds. The Start button should start flashing. Finally, hold the Start and Select Cycle button down for five seconds. The dishwasher control panel should now light up, and the dishwasher should be ready to go.
How do you test a latch switch on a GE dishwasher?
Simply open the door, close the latch and select a cycle and depress the switch. Note that if the test is successful, with the door open, the dishwasher will operate and water may spray out. Make sure to first remove all tools from inside the dishwasher. Do not reach inside the dishwasher during the test.
Do GE dishwashers have a reset button?
You can reset a GE dishwasher by pressing the Start or Reset button. If you have a top-loading dishwasher, you need to open the top, press the button, and close it. Wait 2 minutes for the dishwasher to drain the water. Add any additional dishes after 2 minutes.
How do I reset my old GE dishwasher?
Try pressing the “Start/Reset” pad to reset the dishwasher and wait 2 minutes. If the problem persists, reset (reboot) the dishwasher by turning off power to the unit at the house circuit breaker or fuse box for 30 seconds. Restore power and the dishwasher should reset and function normally.
How do I reset my GE dishwasher without reset button?
If the machine still does not work and won’t reset, reboot it by turning off power to your home for ten minutes, then turn it back on. In order to restart a GE dishwasher, detach the power cord from the outlet. Doing so will reboot and reset the machine and should fix any problems with it.
Why is my GE dishwasher not starting?
The GE dishwasher will not start if the door is not closed properly or the control panel is locked. Power issues that may affect your dishwasher starting include blown fuses, a tripped breaker and disconnected power. The dishwasher also will not start if the water valve is turned off.
How long does diagnostic test take on dishwasher?
The Service Diagnostics Cycle will start when the door is closed. Let it run all the way through, takes about 25 minutes. The CLEAN LED will flash the ERROR CODE in two parts.
How do I reset my dishwasher thermostat?
How to Reset a Dishwasher Thermostat Hold either side of the dishwasher’s bottom front panel, which is located right above the ground. Locate the dishwasher thermostat. Press the button on the underside of the thermostat and hold it for 10 to 15 seconds, then release it. Place the panel back on the dishwasher.
How do you run a diagnostic cycle on a KitchenAid dishwasher?
To invoke a Diagnostics Cycle, press the “Heated Dry” key followed by the “Normal” key then again the “Heated Dry” key and finally “Normal” key, once more. Ensure your machine is in standby mode while doing it (and press the keys rapidly).
How do I put my GE dishwasher in service mode?
GE dishwasher Service Mode (a few other models) The Service Mode (in a few other models) is entered by pressing then holding down “Cycle Select” pad for about 5 seconds (it is possible to switch to the service mode only during Error Code Display/Diagnostic Mode).
How do you reset a GE washer?
Motor Reset Procedure: Unplug the washer for 1 minute from the electrical outlet. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. The motor has now been reset and is ready for you to start a cycle.
Why is my dishwasher door not latching?
A dishwasher door will not close properly if the plastic tub misaligned or is not installed correctly, or if the door latch has malfunctioned. You’ll face the same problem if the top or bottom racks inside aren’t set correctly or if the door striker is misaligned.
How do I clear E4 error on GE dishwasher?
Comments: E4 unplug and unhook. Disconnect the overflow, tilt and drain. I unplugged the dishwasher, cleaned out all water and trap, dry everything inside, unhooked the overflow and drain remaining water out, plugged it in and it worked.
How do I fix e1 error on my GE dishwasher?
Ensure Drain Hose is Installed Properly. Improperly installed drain hoses are a common defect with a lot of dishwasher installations. Use the Proper Detergents. Make Sure Your Door Isn’t Leaking. Make Sure You’re Loading Dishes Properly.
What do you do when your dishwasher won’t turn on?
Check the Power Supply. If the dishwasher won’t do anything at all, the problem could be the power supply. Inspect the Door Latch. Check the Child Safety Lock. Reset the Dishwasher. Turn Off the Power Before Disassembling the Dishwasher. Test the Door Latch Switch. Test the Timer. Test the Selector Switch.
Where is thermal fuse on GE dishwasher?
The thermal fuse is mounted on the control board housing. Push down the main release tab to release the fuse from the locking tabs. Pull the thermal fuse forward and out from under the other tabs.
How do I start my GE dishwasher without the start button?
How do you start a ge dishwasher without the start button? Make sure the dishwasher door is securely latched. Check your electrical box for blown fuses, and reset if blown. Unlock the control panel by pressing and holding the “Heated Dry” button for three seconds. Turn the water valve underneath the sink on.
