Table of Contents
How do I know if my furnace control board is bad?
If a control board starts to break, you will notice some of the following signs of malfunction: Warning lights. Typically, control boards have LED indicators that function as warning lights. Temperature instability. Interruptions in the event sequence.
How much does it cost to replace a circuit board in a furnace?
A furnace circuit board replacement can cost between $550 – $1,100, depending on how complex your system is.
How do you reset a furnace control board?
Follow these simple steps: First, turn off the power supply to the furnace by turning off the breaker in the circuit box. Locate the reset button on the furnace and press it to reset the furnace. If the button is popped up, press it down. Return the cover to the blower compartment and turn the power on.
How long should a furnace circuit board last?
A furnace circuit board lasts 10 to 15 years on average, depending on the furnace condition, usage, and level of maintenance.
When should I replace my furnace control board?
If it is already 15 years old, getting a new circuit board may only add another five years or so to the life of the furnace. On the other hand, investing in a new furnace means you will have between 15 and 20 years of life.
How do you test a control board?
To test circuit board properly, touch the multimeter probes to the test points present on the board. Make sure while playing out this step you have your hands on the plastic portion of the probes. You can then go on to check either the voltage or resistance.
What do you do when your furnace doesn’t turn on?
What to Do When Your Furnace Won’t Turn On Check Your Circuit Breakers. Even if you use a gas or propane furnace, some of the components run on electricity. Check Your Thermostat. Check the Drain Pan. Check Your Air Filter. Check the Pilot Light. Check Your Natural Gas or Oil Supply.
How long does a furnace last?
A well-maintained furnace can last at least 15 to 20 years, but completing annual maintenance and being diligent with repairs can extend its life even longer.
What causes circuit boards to burn?
Boards might burn because of poor protections. A high voltage protection diode protects the board from burning in the event of a lightning strike or other voltage surges. If the board connections are hooked up incorrectly or attached to the wrong type of power supply, leading to eventual burn out.
How much is a circuit board for a York furnace?
Compare with similar items This item 031-01140-702 – OEM Upgraded York Furnace Control Circuit Board 031-01972-000 – OEM Upgraded York Furnace Control Circuit Board Add to Cart Add to Cart Customer Rating 3.2 out of 5 stars (3) 4.5 out of 5 stars (24) Price $12397 $127.95$127.95 Sold By North America HVAC North America HVAC.
How do you replace a motherboard on a furnace?
Control Board Replacement Ensure that the power to the furnace is off. Mark all of the wires and write down which connections they go to on the board. Remove the wires. Remove the old board (The board may be held in place by screws or plastic clips. Attach the new board with the screws or snap it in with the plastic clips.
Do all furnace blower motors have a reset button?
All furnaces are equipped with a reset button. They are generally red or yellow and are located inside the blower compartment. The reset button is a safety feature that will shut down the furnace when a problem is detected, often a hot or overheating furnace, before it trips the circuit breaker.
How many times can I hit the reset button on my furnace?
Don’t hit “reset” more than twice. The process pumps oil into the burner chamber, where it can accumulate if you have no ignition. Then when the furnace finally does start, it can do so explosively. So if the button won’t reset, or quickly pops up again, it’s time to call a professional repair service.
Why is my furnace not blowing hot air?
First, check to make sure the thermostat is set correctly. You will want to make sure that the fan control is set to auto, and not ‘on’. If the thermostat appears set correctly, turn off your heater at the thermostat and check the filter. If the filter is dirty, replace it.
How much does a circuit board cost?
A circuit board typically costs from 50 cents to $300 dollars to produce, depending on your needs. The price to produce a circuit board has many different factors, and may depend on the number layers, complexity, quantity and components included on the board.
Why do control boards go bad?
Failed transistors: The transistors in the control board are susceptible to damage due to power surges, static electricity, and age. Transistors are often the first part of a control board to fail. Loose wiring: The vibrations of the furnace over the years can cause wiring in the control board to shake loose.
Do old furnaces have control boards?
Gas Furnace Control Boards This type of board is a simple ignition control board usually found in older units, which tend to be less energy-efficient. It controls the operation of the gas valve, ignitor, and flame sensor.
