Table of Contents
How do you apply Thompson’s water sealer to concrete?
Brush or roll the product on a hardened concrete surface as an alternative to spraying. When applying it to a vertical surface, start at the bottom and work upward. When using it as a concrete curing agent, apply it at the rate of 1 gallon per 200 square feet.
Can you use Thompsons Water Seal on concrete driveway?
The Thompson’s WaterSeal Clear Waterproofer is a multipurpose product that can be used on wood, brick and concrete. The same formula has been around for years without any new or innovative efforts to improve the performance.
How long does Thompson’s Water Seal last on concrete?
Apply Thompson’s WaterSeal when the temperature is above 50 degrees Fahrenheit and you expect it to stay that way for at least 24 hours. Do not use the product if rain is forecast.
What is the best way to apply sealer to concrete?
How to Apply Concrete Sealer Remove all oil, grease, stains, dirt, and dust from the concrete. Strip any existing sealer from the surface. Open up the concrete with an etching solution. Apply a thin coat of sealer using a roller or sprayer. Wait for the first layer of sealer to dry.
Is Thompson Water Seal any good?
– Thompson’s® WaterSeal® Clear did not alter or change the appearance of the wood. After full drying, we tested the ability to repel water. Water did bead on top of the finish and did not absorb into the wood. – As far as we can tell, Thompson’s® WaterSeal® does not prevent UV graying at all.
What can I put over Thompsons Water Seal?
You can only paint over Thompson’s Water Seal if you wait 45 days and use a primer. This only works if you paint over concrete, but paint doesn’t always stick to the Thompson’s seal well. Your paint may not look as intended because Thompson’s Water Seal has hydrophobic tendencies.
How does Thompsons Water Seal work?
Thompson’s® WaterSeal® Penetrating Timber Oil is an oil-based product that provides protection by penetrating into wood pores and sealing out water infiltration. Thompson’s® WaterSeal® Waterproofing Stains are water-based products that have film-forming properties to protect the wood by repelling water.
Should you water seal bricks?
Historically, a sealer was a product that completely sealed the brick from moisture and air. A waterproofer is a product that keeps the water out but allows the brickwork to breathe. In a nutshell – you should use a waterproofer that allows the brickwork to breathe.
Is Thompsons Water Seal breathable?
Thompsons Water Seal, provides a clear long lasting waterproof seal, stops moisture, water or damp penetrating your exterior walls. Silicone micro emulsion is breathable and provides excellent protection for brick-work, aged concrete, render, slate, painting, terracotta and wood, exterior use only.
How often should you use Thompson Water Seal?
Thompson’s WaterSeal includes a complete line of deck sealers and stains for protecting deck wood from moisture and sunlight. Applying a sealer and/or stain typically is recommended every one to three years, depending on the finishing product, deck use, weather conditions, and sun exposure.
What is the difference between concrete sealer and Waterproofer?
Concrete sealers and waterproofing compounds perform similar functions in different ways. Sealers primarily form protective layers over concrete surfaces, while waterproofing compounds penetrate into surfaces to fill in gaps.
Should I use Thompson Water Seal on pressure treated wood?
Although the wood is resistant to rot and insect attacks because of the pressure treatment, it can warp, split and develop mildew if not protected from the effects of water. The directions for some, such as Thompson’s Water Seal, specify pressure-treated wood as a suitable use.
How many coats of Thompson water Seal do I need?
One coat is enough, but if more color is desired, a second coat can be applied within two hours before the first coat has dried. With Thompson’s® WaterSeal® Waterproofing Stains, you can clean your tools with soap and water.
What is the best sealant for pressure treated wood?
Best Deck Sealers for Pressure-treated Wood Ready Seal 520 Exterior Stain and Sealer for Wood. SEAL-ONCE Nano+Poly Ready Mix Penetrating Wood Sealer. #1 Deck Premium Semi-Transparent Wood Stain for Decks. Thompsons Waterseal Solid Waterproofing Stain. Eco Advance Wood Siloxane Waterproofer Concentrate.
How do you Waterproof untreated wood?
There are three surefire ways to waterproof your wood for years to come. Use linseed or Tung oil to create a beautiful and protective hand-rubbed finish. Seal the wood with coating of polyurethane, varnish, or lacquer. Finish and waterproof wood simultaneously with a stain-sealant combo.
What temperature do you apply Thompson’s water Seal?
Be sure that both surface and air temperatures are above 50°F during application and remain above 40°F for 48 hours after application. Do not apply product if rain is forecasted within 24 hours of application.
Can you apply Thompson’s water Seal with a sprayer?
Answer: The manufacturer of Thompson Water Seal recommended that you use their product with a plastic sprayer with a brass wand, such as our Chapin Premier sprayer. Once you are done with the product, it is recommended that you run mineral spirits through the sprayer and then water to clean it.
Can I mix stain and Thompson’s water sealer?
As long as it’s all oil based you should be able too. But if it’s a solid color stain it might turn a little transparent if mixed with the sealer..just give it a try on a scrap piece. Bingo. As long as they use the same solvents, it should be fine.
How do you remove Thompson’s Water Seal?
Steps to Remove the Sealant: To use mineral spirits, wipe the spirits over the area with a cloth. Let it sit for a few minutes, then scrub the area with a scrub brush. To use a concentrated degreaser, follow the instructions on the label of your selected product.
Should you put sealer on concrete?
You do not have to use a cure and seal, but it is important to seal your concrete. Sealing your concrete will protect it against damage and deterioration against water absorption and surface abrasion. Sealed concrete is more resistant to: Cracking, spalling, and pitting.
Does concrete sealer keep water out?
Penetrating Concrete Sealer Prevents Moisture Problems Excess moisture in concrete is a damaging force to concrete and any materials resting on top of it.
What kind of roller do you use for concrete sealer?
Apply concrete sealer with a 3/4-inch nap paint roller. It’s specifically made to handle rough surfaces such as plaster and concrete. According to Deco-Crete Supply, coat the roller with a small amount of sealer in order to avoid roller lines. Keep the pressure light, and roll evenly over the concrete.
