Table of Contents
To measure your draw length, stand with your back to a wall stretching your arms out against the wall. Measure the distance from the end of your middle finger to the end of your other middle finger, basically the length of both arms, hands and chest. This measurement, minus 15 then divided by 2, is your draw length.
How do bow manufacturers measure draw length?
Draw length is measured from the apex of the bowstring to the deepest part of the bow’s grip, plus 1.75inches.
How much does it cost to get a bow draw length adjusted?
The changing out of the modules usually requires a hexagonal wrench and can be done without pressing the compound bow. While certain companies will offer lifetime modules changes, most new modules have to be purchased. Average cost is $8 to $25.
Is 70 lb draw too much?
For example, a bow with a 70-pound peak weight and a 80% let-off should have a holding weight of around 14-pounds. Being able to hold a bow at full draw for 30 seconds is great, but if you’re shaking, struggling, and exhausted at the end of that time, then you’re not going to be able to make an ethical shot.
How long should my arrows be for a 27 inch draw?
The arrow must be 29″ in length and supported by two points, which are 28″ apart. The number of inches the arrow deflects or bends due to the weight, is the spine size or measurement of an arrow. DYNAMIC spine describes the way an arrow reacts from the stored energy of a bow as it is shot.
How do I find my actual draw length?
To measure your draw length, stand with your back to a wall stretching your arms out against the wall. Measure the distance from the end of your middle finger to the end of your other middle finger, basically the length of both arms, hands and chest. This measurement, minus 15 then divided by 2, is your draw length.
How do you measure bow length?
ANSWER: The easiest way to measure the length of your traditional bow is to start at the string groove, follow the curvature of the limb along the belly side of the bow, across the riser area, and follow the curvature of the other limb to the other string groove. This will give you the a.m.o. bow length.
How do you change the draw length on a prime bow?
Pushing the limb stops inward will result in decreased let-off and shorter draw length, while moving the limb stops outward increases let-off and draw length. To adjust them, use a 9/64” Allen wrench, loosen 8-32” cap screw one full turn, and slide both the upper and lower limb stops equal amounts.
What draw weight do most hunters use?
Some shooters are capable of shooting 70, 80 or 90lbs, but most adult males shoot between 60 and 70lbs. Today’s bows are extremely efficient and 40lb compound bows are more than capable of harvesting many big game animals. For whitetail deer hunting anything above 40 lbs is fine.
What draw weight should I shoot?
As a rule of thumb, 40 pounds of kinetic energy efficiently kills whitetails, and 50 pounds or greater is required for larger game such as elk, moose or bear. When I bought my first Mathews bow, it had a 70-pound draw weight.
What is the highest draw weight compound bow?
The heaviest longbow draw weight is 90 kg (200 lb), achieved by Mark Stretton (UK) at the shooting grounds of The Bath Archers, Somerset, UK, on 15 August 2004. The bow was made by Bickerstaffe Bows (UK), of yew wood, backed with hickory.
How long should arrows be for a 30 inch draw?
The Easton spine chart recommends a spine of 250 for a 30-inch arrow shot from a bow set at 70 pounds. Cut that arrow length down to 28 inches, and the spine chart recommends a 340 spine.
How long should my arrows be for a 29 inch draw?
it depends on the arrows you choose, you need at least 1/4″ of arrow overhang on the rest. so you can probably shoot an arrow that’s about 28 1/4 for rests that are set up normally. and go all the way up to full length 36″ arrows for indoor. i would suggest 1″ of overhang on your rest.
How long should arrows be for a 28 inch draw?
If you’re a 28-inch draw length and want an arrow that ends at the front of the riser, your arrow length would be around 27 inches. However, your arrow length can be longer if you need to weaken the spine of your arrow. For safety reasons, your arrows shouldn’t be cut too short.
What is the average draw length?
If you have an average draw length of 27 to 29 inches, any modern compound bow matched with a good arrow and set to 60 pounds will work just fine on whitetails, mule deer, pronghorns, and the like with whatever broadhead style you prefer, so long as your shot placement is good.
How do I know if my draw length is too long?
The bow arm should move toward the target when the shot is fired. If the bow arm drops or swings to the side, the draw length is probably too long. When this happens, the scapula has already pushed the bow arm out as far as it can extend before the arrow is released.
How do I know what draw weight my bow is?
Draw weight is the amount of force needed to pull a bow, and it’s measured in pounds. Recurves and longbows have incrementally heavier draw weights the farther they’re pulled. The standard for determining their draw weight is taken at 28 inches of draw length.
What is bow AMO length?
AMO length is a standard measurement of bow length that is designated to be three inches longer than the bowstring. For example: If your bow has an AMO length of 60″, the length of your bowstring, and the actual length of your bow when strung, will be 57″.
What does 400 mean on an arrow?
The numbers refer to the spine of the arrow. The different spines refer to the stiffness, a 400 spine arrow is generally for bows 40-60 lbs. 350 spine is for bows roughly 55 – 75 lbs, and a 500 spine arrow is for bows roughly 30 – 50 lbs.
