Table of Contents
Press the button that says Pause/Cancel twice. Now hold the button for a few seconds, until the display is blank. If the F21 error continues to flash on your display, switch the washer off and unplug it. Then plug it back in and switch it on.
How do I fix the code F21 on my Whirlpool washer?
The first step is to try to reset your washer. Sometimes your washer might display the F21 error code when it shouldn’t, and a simple reset will get your washer working again. To reset your washer, you simply need to press “Pause/Cancel” to cancel the current wash cycle.
How do you clear the error code on a Whirlpool front load washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
How do I get rid of Whirlpool washer error?
Manual Review Unplug the Whirlpool washing machine from the mains. Wait for 15-20 minutes while the control unit reboots. Reset the error by pressing the START button (On/Off). Check hatch locking.
How do I factory reset my Whirlpool washing machine?
Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset. You can run a test load without any clothing to ensure that the reset worked.
How do you reset error F21?
Reset. When the “F21” error code appears, try pressing “Pause/Cancel” to stop the current wash cycle. If water remains in the washing machine tub, touch “Drain/Spin” to force a secondary drain cycle to remove the water. Once all the water drains, try selecting a new wash cycle and pushing “Start.”.
Why is my Whirlpool washer flashing F21?
If you see error code F21 on your Whirlpool washing machine, this refers to a water drain problem. The washer won’t be able to finish the cycle and your laundry will be wet. This error code means draining is taking too long, and something is wrong with the water pumping.
How do I clear the error on my Whirlpool Duet washer?
Press the “Pause/Cancel” button on the control panel twice to clear the error. Contact a certified repair technician if pressing the “Pause/Cancel” button does not clear the error, as this indicates that a component has failed in the washing machine or dryer.
How do I reset my Whirlpool Duet front load washer?
Unplug the washer for 30 seconds to attempt to reset the Duet washer control. if your fill hoses have a flood stop check valve turn the water off, disconnect the hoses and run a little water into a bucket. Then reconnect the hoses to your washer and do a Duet Washer Quick Diagnostic Test.
How do you reset a front load washer?
How to reset the washing machine: Press POWER to turn the washer off. Unplug the washer from the power outlet or turn the circuit breaker to the unit off. With the power disabled, press and hold the START/PAUSE button for 5 seconds. Plug the washer back in, or turn the circuit breaker back on.
Why does my washing machine keep saying error?
Common appliance codes could be related to a problem with the door, a water heating sensor, a software or circuit board fault, a motor or pump fault plus much more. Simple things that could have an error code could be the door being left ajar on the machine or the detergent drawer not in situ properly.
How do I fix E1 error on my Whirlpool top load washer?
E1 – water inlet alarm Check that the water faucets are not closed. Check that the water pressure in the house is over 20 kPa. Clean the inlet hose filter screens. Be careful not to remove or disturb the screen placement. Check that the drain hose is not below 27½” (700 mm) from the floor.
What does F28 mean on Whirlpool washer?
The digital display on the Whirlpool Duet washer, at times, will display an error code to alert you of a problem with the washer. An F28 error code is a common problem that means there is a communication problem with the central control unit. This problem is generally solved by essentially rebooting the control unit.
Is there a reset button on a washing machine?
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.
How do you reset a washing machine sensor?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
How do I clear my F21 code on my Maytag washer?
Possible Causes and Action: Unplug the washer or disconnect power for one minute to remove the code. Check the door switch/lock unit for signs of breakage or missing screws. Plug in the washer or reconnect the power. Re-select the cycle and press START.
How do I fix error code F21 on Kenmore?
This may be an indication of a drain pump problem and/or clog in the drain line. Unplug your machine for 1/2 hour to see if the CCU will reset. If that is without result check the drain hose for kinks or if it is clogged. After that check the electrical connections to the pump and ensure the pump is running.
How do I clear the error code on my Kenmore washer?
How to Reset the FH Error Code on a Kenmore Elite Washing Machine Look for the “Pause/Cancel” button on the washer control panel. Press the “Pause/Cancel” button twice to cancel the wash cycle. Connect the water supply hoses back to the washer and turn on the water spigots.
