Table of Contents
Your drawer box should be 17” wide, 5-1/2” tall and 22” deep.
How deep should I make my drawers?
Drawer depth or height is not critical, but the most common difference between the drawer and the opening is 3/4 inch. For example, if the opening measures 4 inches vertically, the drawer should be built 3 1/4 inches. This allows 1/4 inch at the bottom where the slide is attached, and 1/2 inch at the top for clearance.
What depth drawer slides do I need?
Start at the back of the box and measure to the front of the box without including the face of the drawer. Once you have the length, round the number down. For example, if the drawer is 20 ½ inches long you will need to purchase 20 inch drawer slides.
How do you measure for drawer boxes?
Measure the cabinet opening height (inside frame to frame) and subtract at least 1/2” from the opening height. If your cabinet opening measurement comes to 3 3/4″ then you need to round down to a 3 1/2″ drawer box. For depth, we recommend subtracting 1″ from the length of the side-mounted drawer glides.
What is the standard depth of a drawer?
Depth: Standard depths are 14-inches, 16-inches and 20-inches. Height: The height of the drawer refers to the height of the drawer face. The actual height of the box is usually less.
How is drawer depth measured?
Begin by measuring along the bottom floor of the drawer at the back edge, middle, and front edge. Check for variations across the height of the drawer as well. Take the smallest of these measurements. Repeat this step for the depth measurement on the left edge, middle, and right edge across the floor and the height.
How is cabinet depth measured?
Depth: Measure the side of your cabinets, from the cabinet front to where it meets the wall. Standard cabinets are 24 inches deep.
How thick are drawer slides?
Light duty slides might be as thin as 1/2″, while heavy duty slides may be over 3/4″ thick. Face frame cabinet slides are easier to install using the specific, optional, face frame brackets. Length sizing is usually simplified by checking manufacturer’s charts, where the drawer size and cabinet depth are both stated.
Can drawer slides be shorter than drawer?
You should always use the longest slide possible for your application, without exceeding the drawer depth into the cabinet. The Height of a Drawer Slide is usually only a limiting factor, in the sense that you can’t install a slide that is taller than your drawer or pull-out.
What sizes do drawer slides come in?
Shop by Drawer Slide Size Below 8-10″ Drawer Slides. 1-8″, 2-9″ and 9 versions of 10″ drawer slides from Hettich, Fulterer, and Hawthorne & Reid. 12″ Drawer Slides. 14″ Drawer Slides. 16″ Drawer Slides. 18″ Drawer Slides. 20″ Drawer Slides. 22″ Drawer Slides. 24″ Drawer Slides.
How do you measure drawer length?
Measure from the back of the drawer-front to the end of the drawer box. Only measure the box, do not include the drawer front. Round the measurement off to the lower number on the tape. For example, when the measurement is 22 1/2 inches, you need to purchase 22-inch drawer slides.
How deep should closet drawers be?
Drawers for folded clothes should be set at a minimum of 18” (45.7 cm) with deeper drawers for multiple rows of folding clothing at a depth of 24” (61 cm). Deep drawers are consistent with standard closet depths 24” (61 cm).
How deep is a dresser drawer?
What Is the Standard Depth of a Dresser Drawer? The overall standard measurement of a dresser drawer is 60-inch wide, 20-inch deep, and 30-inch tall. Moreover, the drawer depth or height is not a complex thing. But the most common difference between a drawer and an opening is 3/4 inch.
How do you measure depth?
Commonly abbreviated as D, depth is a measurement of how far back a three-dimensional object is. For example, measurements of an object, such as a computer monitor, are commonly measured as (D x W x H), short for Depth by Width by Height. In the illustration, the Z-axis is the depth.
How big should drawer boxes be?
Your drawer box should be 17” wide, 5-1/2” tall and 22” deep. The main thing you should take away from this article is that the only fool-proof way to measure drawer boxes correctly is to consult the specs or installation instructions for the hardware you plan to use.
What are standard drawer sizes?
Here are some of the most common. Small Dresser Drawers: Width – 12″, Depth – 14″, Height – 4″ Medium Dresser Drawers: Width – 28″, Depth – 16″, Height – 6″ Large Dresser Drawers: Width – 30”, Depth – 18”, Height – 8″.
Does cabinet depth include door?
The standard size of a base cabinet is 34.5 inches tall without the countertop and 36 inches with the countertop. If the cabinet is a full height base cabinet (one that only includes a door), that door is 30 inches tall. As far as depth goes a standard base cabinet is 24 inches deep.
How are cabinet boxes measured?
From the opening, you need to measure the width – from side to side horizontally – and height -from top to bottom vertically. The opening is the space that the new box fits in. There two types of mount guides that you can choose when installing drawer boxes. Each mount changes the measurements of the opening.
How thick are bottom mount drawer slides?
10″ Bottom-Mount Drawer Slide Kit, Steel Tracks, 1.2 mm Thick, 1-Pair, White Powder Coat Finish, 2-Pack.
What kind of wood is used for drawer boxes?
Poplar is a great all-around choice for drawer box construction. It is stable, durable, and much less expensive than most hardwoods. The color of poplar heartwood ranges from a creamy white to a yellowish tan or brown. It is very easy to work with and has straight, uniform grain.
