Table of Contents
A standard dresser has between six and nine drawers, is around waist tall (26″ – 44″), is 36″ – 60″ wide, and is 16″ – 20″ deep.
How big should a dresser drawer be?
Dresser drawers should be no more than 36 inches wide. Specifically, states Squidoo.com, a “standard size pine chest of drawers” is typically sized in either “17-inch width, 24-inch width, 30-inch width or 36-inch width” drawers.
What is the standard size of a drawer?
Depth: Standard depths are 14-inches, 16-inches and 20-inches. Height: The height of the drawer refers to the height of the drawer face. The actual height of the box is usually less. Standard heights are 5-inches, 7.5-inches, 10-inches and 12-inches.
How deep should drawers be?
Drawer depth or height is not critical, but the most common difference between the drawer and the opening is 3/4 inch. For example, if the opening measures 4 inches vertically, the drawer should be built 3 1/4 inches. This allows 1/4 inch at the bottom where the slide is attached, and 1/2 inch at the top for clearance.
How do you measure the depth of a drawer?
Begin by measuring along the bottom floor of the drawer at the back edge, middle, and front edge. Check for variations across the height of the drawer as well. Take the smallest of these measurements. Repeat this step for the depth measurement on the left edge, middle, and right edge across the floor and the height.
How deep should bedroom drawers be?
Drawers for folded clothes should be set at a minimum of 18” (45.7 cm) with deeper drawers for multiple rows of folding clothing at a depth of 24” (61 cm). Deep drawers are consistent with standard closet depths 24” (61 cm).
How do you find the area of a drawer?
Measure the height and width of the drawer opening and add 1-1/2 inches to get the face size of the drawer. For example, if the drawer opening measures 18-by-22 inches, you will need to cut one piece 3/4-by-19 1/2-by-23 1/2 inches.
How thick should a drawer bottom be?
The sides and back of the drawer should be 1⁄2” or 5⁄8” thick. Use thinner stock for smaller drawers and thicker stock for big ones. The bottom is usually 1⁄4“-thick plywood for small drawers or 1⁄2“-thick material for bigger drawers, or drawers that will hold heavy objects.
Is a 36 inch drawer too big?
A deep, wide drawer does have a limit in size. You just can’t do a wide drawer at 36” wide or more, because it will sag over time, even with heavy duty glides. Homeowners might tend to weigh down that drawer with big, heavy items and you have to account for that happening somewhat.
How big is too big for a drawer?
The rule of thumb is 1.5 times the length of the drawer slide. If you have a standard depth kitchen cabinet then the normal length of drawer slide is 22”. If you multiply 22” x 1.5 = 33”. You can go wider, but the wider you go the more chance that the slide will not pull out as smoothly as you hope or expect.
How thick are drawer slides?
Light duty slides might be as thin as 1/2″, while heavy duty slides may be over 3/4″ thick. Face frame cabinet slides are easier to install using the specific, optional, face frame brackets. Length sizing is usually simplified by checking manufacturer’s charts, where the drawer size and cabinet depth are both stated.
What is a standard closet depth?
A clothes closet should have a minimum depth of at least 24 inches deep, so the clothes can clear the back wall. Shelves for women’s shoes should be spaced about 6 to 7 inches apart. Shelves for folded clothes should be placed around 12 inches apart.
What are the dimensions of a chest of drawers?
How big are dressers? Dressers come in a large range of sizes to meet varied storage demands, but dressers commonly have overall depths between 18”-24” | (46-61 cm), heights between 30”-50” (76-127 cm), and widths between 30”-74” (76-188 cm).
What are standard closet dimensions?
A typical reach-in closet is approximately 6-feet long, 8-feet high, 24-inches deep with an 80-inch high door opening. Reach-in closets are very practical for a single occupant. They allow for easy viewing and access to all contents. Accessories and baskets work well in them.
How much is plywood for drawers?
Plywood for most drawers is 1/4 inch thick but can be 1/2 inch thick on large drawers. You can find these materials in many different types of hardwood so that one or both of the outer veneers can match your drawer boxes and/or fronts.
How do I choose a drawer slide size?
Measure the box, not the drawer front Start at the back of the box and measure to the front of the box without including the face of the drawer. Once you have the length, round the number down. For example, if the drawer is 20 ½ inches long you will need to purchase 20 inch drawer slides.
How deep should a drawer bottom groove be?
On a table saw, set the cut height for a little more than half the thickness of the drawer side material, and cut a groove to fit the thickness of the drawer bottom material. A good spot for the groove is approximately 3/8″ from the bottom edge of the drawer sides.
What is the bottom of a dresser drawer made of?
The most common materials for drawer bottoms are 1⁄4” hardboard or plywood. For small and medium-size drawers, hardboard will stand up to a moderate amount of weight. For a heavier load, you can step up to plywood. Baltic birch plywood is a great choice.
Is 1 2 plywood strong enough for drawers?
Drawer box side thickness should be at least 1/2″ but if you can find 5/8″ plywood your boxes will be stronger. 1/4″ thick plywood is good enough for most drawers. PureBond 1/4″ Maple Plywood is great for drawer bottoms. Another good choice that is about 1/2 the cost is 1/4″ Tempered Hardboard .
