Table of Contents
The standard depth is 12 inches, but you can find other sizes, from 15 to 36 inches.
What is a standard kitchen drawer size?
Standard non-custom kitchen cabinetry generally offers drawer widths from 12 inches to 24 inches, increasing by 3-inch increments. If the standard drawers available don’t fit into your kitchen design, you can order custom drawers from a cabinetmaker.
How deep should drawer be?
Drawer depth or height is not critical, but the most common difference between the drawer and the opening is 3/4 inch. For example, if the opening measures 4 inches vertically, the drawer should be built 3 1/4 inches. This allows 1/4 inch at the bottom where the slide is attached, and 1/2 inch at the top for clearance.
How far do kitchen drawers come out?
Lower cabinet drawers have depths from around 17 inches to 23 inches deep while drawers located in upper cabinets may start around 12 inches deep. We’ll look at the different types of drawers to give you a sense of their dimensions in the post below.
How far does a cabinet drawer pull out?
Using a pull that is approximately 1/3 the length of the drawer is a good rule of thumb. For modern cabinetry, you can use extra long pulls that span nearly the entire width of each cabinet.
How deep are bottom kitchen cabinets?
A standard base cabinet should be 24 inches or 61 cm in depth. Since refrigerator manufacturers now make deeper fridges, it directly creates a need for deeper countertops or cabinets. If your kitchen isn’t too large, there are base cabinets as small as 12 inches in depth which can fit into tiny spaces in the kitchen.
How thick should kitchen drawers be?
Drawer Basics The sides and back of the drawer should be 1⁄2” or 5⁄8” thick. Use thinner stock for smaller drawers and thicker stock for big ones. The bottom is usually 1⁄4“-thick plywood for small drawers or 1⁄2“-thick material for bigger drawers, or drawers that will hold heavy objects.
How do you measure the depth of a drawer?
Begin by measuring along the bottom floor of the drawer at the back edge, middle, and front edge. Check for variations across the height of the drawer as well. Take the smallest of these measurements. Repeat this step for the depth measurement on the left edge, middle, and right edge across the floor and the height.
Is a 36 inch drawer too big?
A deep, wide drawer does have a limit in size. You just can’t do a wide drawer at 36” wide or more, because it will sag over time, even with heavy duty glides. Homeowners might tend to weigh down that drawer with big, heavy items and you have to account for that happening somewhat.
How deep is a standard chest of drawers?
If your wall space is limited or your room has a cozier design, consider getting a chest. A standard chest is taller (44″ – 60″), narrower (30″ – 40″ wide), and about as deep (16″ – 20″) as a standard dresser.
How thick are drawer slides?
Light duty slides might be as thin as 1/2″, while heavy duty slides may be over 3/4″ thick. Face frame cabinet slides are easier to install using the specific, optional, face frame brackets. Length sizing is usually simplified by checking manufacturer’s charts, where the drawer size and cabinet depth are both stated.
How deep should kitchen drawers be for pots and pans?
Pots and Pan Drawers are typically about 8-10″ high. We prefer them to be about 30″ in width if your kitchen allows it and 36″ is even better. Their depth will be dependant upon the depth of your base cabinet, which is typically 24″, 30″, or 36″ for standard cabinetry.
What size pulls for 30 inch drawers?
Small Drawers that are 12” or less typically work best with a pull that is 3” to 4” long or a knob that is 1” in diameter. Large Drawers that are 30” to 48″will require a pull that is longer than 8″ or a knob that is 1″ in diameter or greater. Using two pulls or knobs for a large drawer also works great.
Where should drawer pulls be placed?
Pulls should be placed horizontally on drawers. For small drawers (less than 24” wide) center the knobs or pulls in both directions. Just like on larger drawers, pulls should be placed horizontally. Knobs and pulls can also be placed centered at the very top of the drawer panel, where the drawer rail begins.
How do you measure for drawer pulls?
Place the drawer pull on a work surface with the threaded posts facing up. Measure from the center of the screw hole in one threaded post over to the center of the other screw hole with a tape measure. This is the measurement required when selecting replacement pulls.
How deep are upper cabinets?
Standard wall cabinets (sometimes referred to as “upper cabinets”) are 12 inches deep; standard base (below-counter) cabinets are 24 inches deep.
How thick should kitchen cabinets be?
Side and floor panels inside the cabinet should be least a half-inch thick. Side panels should be routed with a groove to support the drawer base. Floor inside the cabinet should be fitted into the routed side panel. Shelves inside the cabinet should be least three-quarters of an inch thick.
How thick are cabinet drawers?
The thickness of a high-quality solid wood drawer side ranges from ⅝” to ¾” thick. A plywood bottom is fitted into grooves on all sides. The most important feature of cabinet drawers is the method of joinery.
How thick should cabinet drawers be?
Drawer box side thickness should be at least 1/2″ but if you can find 5/8″ plywood your boxes will be stronger. Unless you’re building large drawer boxes for very heavy items or large file drawers 3/4″ sides won’t be necessary.
How thick should a kitchen drawer bottom be?
Drawers are typically made with matching plywood bottoms. Plywood for drawer bottoms is available in 1/4″, 3/8″, and 1/2″ thickness. 3/8″ thick plywood is the best overall thickness for drawer bottoms and is available for Maple, Birch, Beech, Cherry, and Walnut.
How do you find the area of a drawer?
Measure the height and width of the drawer opening and add 1-1/2 inches to get the face size of the drawer. For example, if the drawer opening measures 18-by-22 inches, you will need to cut one piece 3/4-by-19 1/2-by-23 1/2 inches.
